Ryobi P4360 Manuel D'utilisation page 149

RYi150BG
OPERATOR'S MANUAL
18 VOLT POWER SOURCE
IMPORTANT SAFETY INSTRUCTIONS
WARNING!
READ AND UNDERSTAND ALL INSTRUCTIONS. Failure to
follow all instructions listed below may result in electric shock,
fire and/or serious injury.
 SAVE THESE INSTRUCTIONS - This manual contains impor-
tant safety and operating instructions for power source model
RYi150BG.
NOTICE:
This product's AC receptacle has a non-sinusoidal output and
is not recommended for use with certain types of sensitive
electronics. Please refer to your product Operator's Manual.
 For use with RYOBI 18 V battery packs, see tool/appliance/
battery pack/charger correlation supplement 987000-432.
 Do not expose the power source to rain or wet conditions.
Water entering the power source will increase the risk of electric
shock.
 Do not use the power source if it has been dropped or
received a sharp blow. A damaged power source will increase
the risk of fire.
 Remove the battery pack from the power source when not
in use.
 This product is for indoor use only.
 Do not disassemble the power source.
 To reduce the risk of injury, close supervision is necessary
when an appliance is used near children.
 Store power source indoors and away from children.
 As with all electrical devices, use caution when plugging/
unplugging other devices into this unit. Do not force plugs
into this unit.
 If this unit is used in a manner not specified by the
manufacturer, the protection provided by this equipment may
be impaired.
 Do not overload the power source. It must be used for pow-
ering devices less than the product rating.
 Two- or three-prong plugs may be used with this product.
Do not force a polarized plug (one prong larger than the other)
into this product. Flip plug over and retry.
 Never block air vents. Blocked vents may cause overheating.
Power source will automatically shut off when overheated.
 Keep power source cool. Do not place near heat vents or in
direct sunlight.
 Do not use the power source around flammable fumes
and gasses, such as in the bilge of a boat or near propane
tanks.
 Do not put foreign objects into the power source.
 Operate this product using only the AC power type listed
in the product specifications.
 This unit should never be hard wired into a circuit.
 Do not power life support devices or other necessary
medical equipment with this power source.
 Save these instructions. Refer to them frequently and use
them to instruct others who may use this product. If you loan
someone this product, loan them these instructions also.
PRODUCT SPECIFICATIONS
Watts ....................................................... 150 Watts Continuous
DC Input ................................................................... 18 Volts DC
AC Output .................................................120 Volts, 1.25 Amps
USB Output ..................................................5 Volt (2.4 Amp) DC
Output Wave Form ...................................... Modified Sine Wave
OPERATION
APPLICATIONS
You may use this product for the following purposes:
 Operating and charging USB-powered devices
 Supplying electrical power for operating compatible small
electronics such as cell phones, tablets, laptops, LED lights,
small fans, radios, etc.
NOTE: This device is not compatible for use with appliances,
power tools, air conditioners, sump pumps, compressors, and/
or other larger electrical devices.
INSTALLING/REMOVING BATTERY PACK
See Figure 1.
 To install: insert a battery pack into the power source as
shown. Make sure the latches on the battery pack snap into
place and the battery pack is secured in the power source
before beginning operation.
 To remove: depress the latches on the battery pack.
USING THE POWER SOURCE
See Figure 2.
When a battery pack is installed, this power source converts DC
electricity to 120V AC household power and/or 5 volt DC USB
(up to 2.4 amp) charging power, allowing the user to charge and
power a variety of devices.
WARNING:
Risk of electric shock. When using a grounded appliance
this tool will not provide an electrical path to earth ground.
Do not power devices with damaged or frayed power cords.
 Insert a battery pack into the power source.
 Press the power button ( ) to turn the power source ON. The
LED will light up green when ready to use.
 Plug devices you want to power or charge into the power
source's USB ports and/or 120 volt receptacle.
 If the power button LED blinks red then turns off, the power
source may be overloaded. Disconnect your device, make
sure your battery pack is sufficiently charged to power your
device, then press the button to turn the power source
back on. Reconnect your device and try again. If the fault
condition immediately reoccurs, the item being powered
exceeds the capacity of the power source.
ILLUSTRATIONS / ILLUSTRÉES / ILUSTRADAS
Fig. 1
C
B
A - Battery pack (not included) [bloc-piles (non inclus), paquete de baterías (no
suministrado)]
B - Depress latches to release battery pack (appuyer sur les loquets pour libérer
le bloc-piles, para soltar el paquete de baterías oprima los pestillos)
C - Power source (bloc d'alimentation, fuente de alimentación)
 If the power button LED turns red but does not shut down
the power source, the power source is overheated. Allow
the unit to cool until the LED turns green, then try again.
 To use the worklight, press the light button ( ). Press the light
button again to turn the worklight off.
NOTE: The power source must be on for the worklight to
function.
 When finished, disconnect your device and press the power
button indicator ( ) again to turn off the power source.
NOTE: When needed, an internal cooling fan will run to regulate
the unit's operating temperature. If running, always wait for the
fan to stop before you disconnect the battery pack from the
power source.
WARRANTY
This product has a Three-year Limited Warranty for
personal, family, or household use (90 days for business
or commercial use). For warranty details, visit
www.ryobitools.com or call (toll free) 1-800-860-4050.
Fig. 2
A
B
A
D
C
B
A
B
E
A - Power button (bouton d'alimentation, botón de encendido)
B - Light button (bouton de lumière, botón de luz)
C - 120 V receptacle (réceptacle 120 V, receptáculo de 120 voltios)
D - AC product to be powered (not provided) [produit à alimenter (non fourni),
producto de CA para ser alimentado (no provisto)]
E - 2.4 amp USB ports (ports USB 2,4 A, puertos USB de 2,4 A)
F - USB product to be charged (not provided) [produit USB à charger (non
fourni), producto USB a cargar (no provisto)]
TECHTRONIC INDUSTRIES POWER EQUIPMENT
P.O. Box 1288, Anderson, SC 29622, USA
1-800-860-4050  www.ryobitools.com
F
995000771
1-22-19 (REV:02)