Publicité
Please read
these
instructions carefully before you start to
assemble this product.
Please
carry
out the
steps
in
the order
set
out
in
these instructions.
Keep
these
instructions
in
a
safe
place
for future
reference.
P
When
encountering the information
icon, please refer
to the relevant
assembly step for additional comments and
assistance.
Cara
...d
cafatv Aduira
For
safety purposes we
strongly recommend the product to
be
assembled
by at least
two
people.
Some parts may have sharp edges. Please be careful when
handling components.
Always wear gloves,
eye
protection,
and long
sleeves
when assembling or
performing
any maintenance on
your product.
Do
not attempt to
assemble the
product
in
windy
or
wet conditions.
Dispose
of
all
plastic
bags safely
-
keep
them out of
reach
of
small
children.
Keep
children away from the assembly
area.
Do
not attempt to
assemble the
product if
you
are
tired,
have
taken drugs,
medications
or alcohol, or if you are prone to dizzy spells.
When using
a
stepladder
or
power tools,
make sure you
follow
the
manufacturer's safety advice.
Do
not climb
or stand
on
the
roof.
Heavy articles should
not
be
leaned against the poles.
Do
not
hang or
lay on
the profiles.
Keep
roof and gutter
clear
of
snow,
dirt
& leaves.
Heavy
snow load
on
roof
can
damage the
product making it
unsafe
to
stand
below
or nearby.
This
product
was
designed and produced to
be used
as
a
Patio cover only.
Some versions
of
this product
are
painted.
If color
was scratched
during assembly it
can be
fixed
with the following tints:
White
-
RAL
9016
Grey
-
RAL
7012
Cleaning Instructions
When
your product
needs cleaning,
use
a
mild detergent solution
and rinse
with
cold
clean water.
Do
not
use
acetone, abrasive cleaners, or others special detergents to clean
the
panels.
Before Assembly
This
product must
be
assembled on
a
solid
base (such
as
concrete or asphalt) and anchored to
the ground.
Choose
your
site
carefully before beginning
assembly.
Sort
the parts and check according to the contents parts
list.
Site surface needs
to
be
leveled (mainly
below the
poles).
Please
consult your
local
authorities if
any
permits
are
required prior to constructing the
product.
Prior
to enlarging the
Patio Cover, several
parts need to
be
dismantled, it
is
recommended to
keep
them
in
a
safe
place
for future
use.
t)uring
Assembly
These
instructions mainly
refer
to the assembly
of the
SideWall on
the right
side
of
the patio
cover.
Assembly
of
the
SideWall on
the left
side
of
the patio cover
is
possible
taking the
same steps.
In
several steps
"Option 1"or"Option
2"
notifications represent the assembly
side selection.
"Option
1" refers
to
assembly on the left
side
while
"Option
2"
refers
to the right.
While
mounting the frame structure to
back wall or
floor the application of
silicone sealant
is
needed
in
order to ensure maximal
sealing.
Step 6:
It
is
important
to assemble the holes outwards
in
order to allow the water to drain out.
Step 20
:
Please
follow
"Option
1"
or
"Option 2"
according to the
side you chose
to mount the
SideWall.
Use
part #7514 when installing the
SideWall on
the left
side
of
the patio
cover.
Use
part #7485 when installing the
SideWall on
the right
side
of
the patio
cover.
Step 23:
In
order to
fit
the
Sidewall, make sure you slide
the front beam to the
pergola's
front
end.
Step 42: Mark the panel to
fit
the
space and
trim accordingly.
Step 45:
Please
insert the sealing rubber (#7473) at the
same
time;
on
both
sides
of
the
panel
as
described
in
drawing 45b.
Step 49:
Please use
the leftovers
of
sealing
rubber (#7473) from step
45.
Note:
The
wall anchoring kit supplied with this product
is
suitable only for concrete
walls.
Other wall types
need an
accordant wall fixation
kit. (Contact
your supplier)
Publicité
