Flexlite FLX1SB Manuel D'utilisateur page 2

GENERAL SAFETY RULES
WARNING!
READ AND UNDERSTAND ALL INSTRUCTIONS.
Failure to follow all instructions listed below may result in electric shock, fire and/or serious personal injury.
SAVE THESE INSTRUCTIONS
WORK AREA
 Keep your work area clean and well lit. Cluttered benches
and dark areas invite accidents.
 Working temperature. This work light is designed to be
used at normal room temperature. If used under 0°C (32°F)
the battery will discharge faster. If used over 45°C (113°F)
an automatic cut-off will turn the light off until the
temperature of the light head comes down. Depending if the
work area is well ventilated or not, the cut-off temperature
can be affected (see features for more information).
 FLEXLITE is designed to be used in industrial environments
under rain, snow and dust. But FLEXLITE products can not
be immersed in water. If the working area is moist and dusty,
some particles will stick to the fan or heat sink and reduce
performance. See maintenance section to remove any dirt.
DANGER!
Never connect / disconnect or use an external power
supply or charger in hazardous area.
DANGER!
Never connect or disconnect the connector on the
light head or any extension cord when the power is on
or in hazardous area.
ELECTRICAL SAFETY
 A battery operated work light FLX1SB must be
connected properly to a Flexlite charger to be recharged.
Using another wall mount charger clip may create a risk of
fire.
SPECIFIC SAFETY RULES
 Know your work light. Read operator's manual carefully.
Learn its applications and limitations, as well as the
specific potential hazards related to this work light.
Following this rule will reduce the risk of electric shock, fire,
or serious injury.
 Lens and housing become hot during use:
 During or immediately after use, don't lay work light flat
on lens surface or place lens area in contact with a plastic
or fabric covered surface.
 Handle work light with care around any flammable
surface.
 Do not use or permit use of work light in beds or sleeping
bags. This work light lens can melt fabric and a burn
injury could result.
 Use only the adapter recommended for use with your
work light. Do not substitute any other adapter. Use of
another adapter could cause batteries to explode causing
possible serious injury.
Use wall mount adapter only with products listed (see
FEATURES on page 5).
SERVICING
 Work light maintenance must be performed only by
qualified repair personnel. Servicing or maintenance
performed by unqualified personnel may result in a risk of
injury.

When servicing a work light, use only identical
replacement parts. Follow
Maintenance section of this manual. Use of unauthorized
parts or failure to follow Maintenance Instructions may
create a risk of shock or injury
STORAGE TEMPERATURE
 Store work light at room temperature between 4 and 27°C
(40 and 80°F) for best results.
 When transporting or temporarily storing in a vehicle,
temperature range should be greater than -30°C (-22°F) but
no more than 66°C (151°F).
 Storing work light at temperatures greater than 76°C
(169°F) for extended periods of time (more than 2 hours)
may cause damage to work light and possible fire or
explosion.
DANGER!
Never store FLEXLITE (battery models)
under direct sunlight.
 Do not charge battery pack in a damp or wet location.
Following this rule will reduce the risk of electrical shock.
 Your battery work light should be charged in a location
where the temperature is more than 10°C (50°F) but less
than 37°C (99°F).
 Do not disassemble your work light.
 Do not permit children to use work light unsupervised. It
is not a toy. The temperature of the light head will become
hot after being on for only a short period of time. This hot
temperature can cause burn injury if touched and can create
sufficient heat to melt some fabrics.
 Stay alert. Watch what you are doing and use common
sense. Do not rush.
 If wrapped or in contact with fabrics, the work light lens
can produce sufficient heat to melt some fabrics. To avoid
serious personal injury, never allow the work light lens to
come in contact with anything.
instructions in the
.
2