Publicité
Les langues disponibles
Les langues disponibles
To use a Manual Cycle
Select a Manual Cycle.
Press MORE TIME or LESS TIME until the desired drying
time is displayed. Tap MORE TIME or LESS TIME and the
time will change by 1-minute intervals. Press and hold
MORE TIME or LESS TIME and the time will change by
5-minute intervals.
NOTE: The More Time and Less Time features can be
used only with Manual Cycles.
4.
5.
6.
•
Press TEMPERATURE until the desired temperature
glows.
NOTE: During a Manual Cycle, you can change the settings
for Time, Temperature, WRINKLE GUARD ®and End of Cycle
Signal. Press PAUSE/CANCEL twice to stop the dryer and
clear the settings. Select another cycle or option.
(OPTIONAL STEP) If desired, select OPTIONS. For more
details, see "Options."
(OPTIONAL STEP) If desired, set the END of CYCLE SIGNAL.
Select HIGH or LOW to alert you when a cycle ends.
Press and hold START for approximately
3 seconds until
dryer starts. Be sure the door is closed.
•
If you do not press Start within 5 minutes of selecting the
cycle, the dryer automatically
shuts off.
•
If you wish to end your drying cycle after pressing Start,
press PAUSE/CANCEL twice.
To stop your dryer at any time
Press PAUSE/CANCEL twice or open the door.
To pause the dryer at any time
Open the door or press PAUSE/CANCEL once.
To restart the dryer
Close the door. Press and hold START until dryer starts.
NOTE: Drying will continue from where the cycle was interrupted
if you close the door and press Start within 5 minutes. If the cycle
is interrupted for more than 5 minutes, the dryer will shut off.
Select new cycle settings before restarting the dryer.
::: :)):;:,1:::
This feature allows you to lock your settings to prevent
unintended use of the dryer. You can also use the Control Locked
feature to prevent unintended
cycle or option changes during
dryer operation.
To enable the Control Locked feature:
Press and hold AUTO DRY LEVEL for 3 seconds. Control Locked
glows and a single beep tone is heard. To unlock, press and hold
AUTO DRY LEVEL for 3 seconds. The indicator light turns off.
Properly loading your dryer can lower your utility bill and prolong
the life of your garments.
Loading suggestions
•
Load the dryer by the amount of space items take up, not by
their weight.
•
Do not overload the dryer. This causes uneven drying and
wrinkling.
Super Capacity
Dryers
Heavy Work Clothes
4 jeans
2 sweatpants
4 workpants
2 sweatshirts
4 workshirts
Towels
10 bath towels
10 hand towels
14 washcloths
Mixed Load
3 sheets (1 king, 2 twin)
9 T-shirts
4 pillowcases
9 shorts
3 shirts
10 handkerchiefs
3 blouses
Select the correct cycle and dryness level or temperature for your
load. If an Auto Dry Cycle is running, the display shows the
estimated cycle time when your dryer is automatically sensing
the dryness level of your load. If a Manual Cycle is running, the
display shows the exact number of minutes remaining in the
cycle.
Cool Down tumbles the load without heat during the last few
minutes of all cycles. Cool Down makes the loads easier to
handle and reduces wrinkling. The length of the Cool Down
depends on the load size and dryness level.
Drying tips
•
Follow care label directions when they are available.
•
If desired, add a fabric softener sheet. Follow package
instructions.
•
To reduce wrinkling, remove the load from the dryer as soon
as tumbling stops. This is especially important for permanent
press, knits, and synthetic fabrics.
•
Avoid drying heavy work clothes together with lighter fabrics.
This could cause overdrying of lighter fabrics and lead to
increased shrinkage or wrinkling.
Cycle tips
•
Dry most loads using the preset cycle settings.
•
Refer to the Auto Dry chart or Manual Preset Cycle Settings
chart (in the "Cycles" section) for a guide to drying various
loads.
Drying temperature
and Auto Dry Level are preset when
you choose an Auto Dry Cycle. You can select a different
dryness level, depending
on your load, by pressing Auto
Dry Level and choosing More or Less.
If you wish to adjust the cycle length of a Manual Cycle,
press More Time or Less Time. Adjust the temperature
of
a Manual Cycle by pressing Temperature until the desired
temperature is selected.
NOTE: You cannot choose an Auto Dry Level with Manual
Cycles.
14
Publicité
