Télécharger Imprimer la page

Publicité

Liens rapides

PVS-4215
FLAT PANEL AUDIO VIDEO SYSTEM
MEUBLE TV POUR TÉLÉVISEURS
SOPORTE PARA TV
ASSEMBLY INSTRUCTIONS
INSTRUCTIONS D'ASSEMBLAGE
INSTRUCCIONES DE ENSAMBLAJE
Patent pending / Brevet en instance / Patent pendiente
Made in China / Fabriqué en Chine / Hecho en China
Italian designed / De design italien / De diseño italiano
HS-2_021109v2T
Do not discard these instructions / Ne pas jeter ces instructions / Conserve estas instrucciones

Publicité

loading

Sommaire des Matières pour Bell'O PVS-4215

  • Page 1 PVS-4215 FLAT PANEL AUDIO VIDEO SYSTEM MEUBLE TV POUR TÉLÉVISEURS SOPORTE PARA TV ASSEMBLY INSTRUCTIONS INSTRUCTIONS D’ASSEMBLAGE INSTRUCCIONES DE ENSAMBLAJE Patent pending / Brevet en instance / Patent pendiente Made in China / Fabriqué en Chine / Hecho en China Italian designed / De design italien / De diseño italiano...
  • Page 2 PARTS LIST / NOMENCLATURE DES PIÈCES / LISTA DE PIEZAS Quantity Quantity Part / Pièce / Pieza Part / Pièce / Pieza Quantité Quantité Cantidad Cantidad Tools Outillage Herramientas...
  • Page 3 FOR YOUR SAFETY, PLEASE FOLLOW THESE PRECAUTIONS: ! ALWAYS REMOVE THE TV AND OTHER EQUIPMENT FROM THE FURNITURE PRIOR TO MOVING THE ASSEMBLED UNIT. ! BE CAREFUL WHEN MOVING THE ASSEMBLED FURNITURE AFTER THE GLASS SHELF HAS BEEN INSTALLED, AND/OR WHEN THERE IS EQUIPMENT LOCATED ON THE FURNITURE AS THIS MAY CAUSE THE SHELVES AND OTHER ITEMS TO BECOME UNSECURED AND FALL.
  • Page 4 ASSEMBLY INSTRUCTIONS INSTRUCTIONS D’ASSEMBLAGE INSTRUCCIONES DE ARMADO NOTE: TWO PEOPLE ARE RECOMMENDED TO ASSEMBLE THIS TABLE. THIS TABLE WILL BE ASSEMBLED IN AN UPSIDE-DOWN POSITION. REMARQUE : IL EST CONSEILLÉ D’ TRE À DEUX POUR ASSEMBLER CE MEUBLE. LE MEUBLE EST ASSEMBLÉ POSÉ À L’ENVERS. NOTA: ES RECOMENDABLE ENSAMBLAR ESTA MESA ENTRE DOS PERSONAS.
  • Page 5 Fig. 2 Fig. 2B Fig. 2A 3. SCREW the Middle Shelf Support Post (H14) into the pre-drilled hole in the front center of the CMS ® Panel (H2) as shown in Fig. 2B. 4. SLIDE the Middle Shelf Leg Cylinders (H5) over the ends of the Long Threaded Rods (H10). CAREFULLY SLIDE the Middle Shelf (H3) (the one without the silver discs) onto the Threaded Rods so that it is sitting on the end of the Cylinder, and PLACE the rear edge of the Middle Glass Shelf under the Shelf Support Post.
  • Page 6 Fig. 3B Fig. 3 Fig. 3C Fig. 3A 6. SCREW the Bottom Shelf Support L-Brackets (H15) into the lower rear inside of the CMS ® Panel (H2) using the Larger Hex Head Screws (H9) as shown in Fig. 3B. 7. CAREFULLY place the front of the Bottom Shelf (H4), onto the end of the Threaded Rods (H10), and POSITION the silver discs at the rear of the Bottom Shelf beneath the two Bottom Shelf Support L-Brackets (H15) as shown in Fig.
  • Page 7 This warranty gives you specific legal rights. You may also have other rights, which vary from state to state. BELL'O INTERNATIONAL CORPORATION, 711 Ginesi Drive, Morganville, NJ 07751-1235 Phone: (732) 972-1333 Fax: (732) 536-6482 Web: www.bello.com E-mail: sales@bello.com...
  • Page 8 Garantía limitada de un (1) año Se le garantiza al comprador original este producto Bell'O International Corporation, con excepción del vidrio, durante un período de un (1) año a partir de la fecha de la compra. Se le garantiza al comprador original el vidrio durante un período de treinta (30) días a partir de la fecha de la compra. Esta garantía se limita expresamente a los productos nuevos comprados en cajas cerradas en fábrica.