Publicité
Les langues disponibles
Les langues disponibles
S H A D I N G S Y S T E M
3
INSTALL THE SHADE:
IMPORTANT: The steps in this section must be performed by two people, with one person supporting each end of the shade. If the brackets are mounted in a location that cannot be reached
when standing on the floor, two ladders are also required. It is recommended that all steps are reviewed by both installers before proceeding.
Connect the Wire Harness to the EDU
a. Position the drive end of the shade near the mounted drive-end bracket, and rotate the shade
toward you so you can see the EDU connector on the back side of the drive mandrel.
Drive
Wire Harness
Mandrel
EDU
Connector
Drive-end Bracket
(wall mount shown)
b. Plug the wire harness (installed in Section
1
) into the EDU connector (i), ensuring it is fully
inserted (ii), then rotate the shade back into the position shown (iii).
i
ii
5
FINAL ADJUSTMENTS:
About Light Gaps
Light gaps are symmetrical at 1⁄ 2 in (12 mm), when the
bracket-to-bracket distance is correct. As noted in section
3
, extension of the spring-loaded idler may add up to
1⁄ 8 in (3 mm) of light gap on the idler end of the shade.
Drive
Idler
Bracket
Bracket
1⁄ 2 in - 5⁄ 8 in
1⁄ 2 in (12 mm)
(12 mm - 16 mm)
04/2024
P/N 045969 Rev. A
Hang the Shade in the Mounting Brackets (Idler End First)
a. Holding both ends of the shade in alignment with the brackets, aim the idler* mandrel at
the bracket-shade interface opening as shown and insert.
b. Push the mandrel into the bracket until it seats with a click.
c. Repeat steps a. and b. at the drive end of the shade.
Rotate the entire shade to
d. After both ends of the shade are pushed in and seated, pull back on the shade to confirm it
view the EDU Connector
is securely locked into both brackets.
Backside View
a.
EDU
Connector
iii
* NOTE: The idler is spring-loaded, with 1⁄ 8 in (3 mm) of travel to allow for installation
tolerance. At the correct bracket-to-bracket distance, the idler will be fully
compressed. Extension of the idler indicates increased bracket-to-bracket distance,
and results in a larger light gap at the idler side of the shade. Refer to section
more information.
Adjust Bracket Positions
If light gaps are not equal, or if telescoping * is
observed, remove the shade and adjust mounting
bracket positions to correct. Ensure the moving shade
does not rub on any part of the bracket.
1⁄ 8 in (3 mm)
adjustment
1⁄ 8 in (3 mm)
adjustment
Jamb
Loosen or remove screws; adjust
Install one or two shims (each adds 1⁄ 16 in [1.6 mm]).
and re-tighten (end bracket shown).
Using more than two shims will impact bracket aesthetic.
* For additional information on telescoping, please see Application Note #14 at www.lutron.com
b.
Idler
Mandrel
Idler
Bracket
6
AESTHETIC TRIM:
Install the Bracket Covers (end and center only)
Position a bracket cover on the mounting surface as shown, and
slide it over the bracket foot to conceal the fastener heads. Repeat
for remaining bracket(s).
End
Center
4
POWER-UP AND ADJUST LIMITS:
POWER: Turn on the supply circuit breaker to energize the power supply and power up the
shade. The shade's LED indicator will flash a multi-color sequence upon power-up. For a complete
guide to LED signals, see: www.lutron.com/TechnicalDocumentLibrary/Sivoia QS Shades.html
LIMITS: Default open and close limits are set at the factory based on the window size entered
with the original order. If adjustment is necessary, follow the steps below to set new limits.
Setting the Open Limit
a. Tap the round button. The green LED will turn on.
b. Use the arrow buttons to jog the shade to the
desired open-limit position.
c. Press and hold the round button until the green LED
flashes. The open limit is now set and stored.
Setting the Close Limit
a. Tap the square button. The green LED will turn on.
b. Use the arrow buttons to jog the shade to the
desired close-limit position.
c. Press and hold the square button until the green
LED flashes. The close limit is now set and stored.
Verify Operation
After limits are set, run the shade up and down several times to verify smooth,
unobstructed operation and straight roll-up.
?
HOW TO REMOVE THE SHADE:
If it becomes necessary to remove the shade for adjustments
or for any other reason, use the frosting knife or the flat-blade
screwdriver as shown.
a. Insert the tool between the mandrel and the bracket.
b. Push the retaining spring (inside the bracket) aside by applying
5
for
pressure on the tool handle toward the center of the shade.
c. With the shade released, withdraw the tool, then the shade.
d. Repeat steps a., b., and c. at the other end of the shade.
Rotate the Finishing Rings
Rotate the finishing ring of each bracket to conceal the bracket-
shade interface opening. The ring features detents that will hold it
in a specific position for best concealment.
Lutron, the Lutron logo and PALLADIOM are trademarks or registered trademarks of Lutron Electronics Co., Inc. in the US and/or other countries.
Chassis Installation & Setup Guide
a.
b.
c.
JOG
TAP
HOLD
a.
b.
c.
JOG
TAP
HOLD
Release
Spring
Push
Lutron Electronics Co., Inc. 7200 Suter Road, Coopersburg, PA 18036-1299, U.S.A.
Publicité
