Lutron Electronics PALLADIOM LMR-C Guide D'installation Et De Configuration

Shade models: LMR-C, LMRJ-C
Chassis Installation & Setup Guide
Important Notes: Please Read Before Installing
A. Plan the installation to maintain sufficient clearance between the shade and any other object,
including window trim, hardware, cranks, lock levers, and drapery.
B. For safety, this product must be installed by two people.
C. The shade system, including the pocket, if applicable, must be mounted to blocking or other suitable
structural material. It is the responsibility of the installer to choose and install fasteners that are
appropriate for the mounting surface such that each shade bracket can support 400 lbs (181.4 kg).
NOTICE: This device is not intended for use by persons (including children) whose physical, sensory
or mental capabilities are different or are reduced, or lack of experience or knowledge, unless such
persons receive supervision or training for the operation of the appliance by a person responsible for
their safety. Children should be monitored to ensure that they do not utilize this device as a toy.
INTRODUCTION:
This guide is intended only for factory trained and equipped installers of Lutron's PALLADIOM
Shades. The following instructions detail wiring, shade bracket mounting, chassis installation,
and setup/operation at a site which has already been planned and prepared using the dedicated
wall, ceiling or jamb installation templates according to the PALLADIOM Installation Planning and
Template Guide.
EDU Model: QSSC-EDU-L | 24-36 V- | 52 W | 10 in-lb (1,12 N•m)
COMPONENTS:
PALLADIOM Shade
Shade Brackets Mounting Bracket
(end brackets shown) Screws Covers
Wireless Bracket Shims
Receiver
Adapter
(LMRJ-C only)
End
TOOLS NEEDED:
#2 Phillips
Driver Bit
3/32 in (2.4 mm)
Flat Screwdriver
Power Drill / Driver
Level or Laser Level
04/2024
P/N 045969 Rev. A
please read before installing
1
SHADE WIRING:
! WARNING: RISK OF ELECTRIC SHOCK. May result in serious injury or death. Lock the
supply circuit breaker in the OFF position before performing the steps in this section.
Shade Wire Harness
a. Tuck the wire harness into the drive bracket as
shown.
* Note the correct orientation of the connector and
wires. Wire colors may differ on harnesses. Refer to
the label on your bracket's specific wire harness.
b. At the other end of the wire harness, strip away 1 in
(25 mm) of the outer cable jacket, then strip 1⁄4 in
(6 mm) of insulation from each conductor.
c. Install the male terminal block, arranging the four
conductors by color and number according to the
diagram at right.
d. For brackets that do not require wiring (idler-side
bracket), trim the harness at the two locations
shown, leaving in place the pre-routed section of
wire that is pressed into the groove on the side of
the bracket.
Power Supply Cable
e. Strip away 1 in (25 mm) of the supply cable's outer
jacket, then strip 1⁄4 in (6 mm) of insulation from
each conductor.
f. Install the female terminal block, arranging the four
conductors according to the diagram at right.
g. Connect the shade wire harness and the supply
cable.
h. Tuck the connectors and excess cabling into the
Finishing Terminal
wire housing.
Rings Blocks
Center Jamb
Wireless Receiver (optional)
The Wireless Receiver Adapter may be spliced into the power supply cable anywhere
between the power supply and the shade. Cut the supply cable at the desired location,
Tape Measure
install the terminal blocks included with the adapter, and connect as shown. Mount the
Wireless Receiver according to the instructions included in the kit.
Wire Cutter / Stripper
From Power
Supply
Female
3/4 in (19 mm) Frosting Knife
Terminal Block
(optional; for shade removal)
Worldwide Headquarters | USA
Lutron Electronics Co., Inc.
7200 Suter Road, Coopersburg, PA 18036-1299 USA
Customer Assistance: 1.844.LUTRON1 (588-7661)
Online: www.lutron.com/help | Email: support@lutron.com
a.
Black Wire
on bottom
c. Press here, insert wire, release.
BLACK
RED
GRAY
VIOLET
d.
BLACK
RED
GRAY
COM
VIOLET
V+
MUX
MUX
f. Press here, insert wire, release.
COM
V+
MUX
MUX
g.
To Wireless Receiver
Wireless Receiver Adapter
(pre-assembled)
To Shade
Wire Harness
Male Terminal Block
European Headquarters | United Kingdom
In EEA imported by: Lutron EA Ltd.
125 Finsbury Pavement, 4th floor, London EC2A 1NQ, UK
TEL: +44.(0)20.7702.0657 | FAX: +44.(0)20.7480.6899
Technical Support: +44.(0)20.7680.4481 | FREEPHONE: 0800.282.107
2
MOUNT THE SHADE BRACKETS:
! CAUTION: RISK OF FALLING OBJECTS. Read and follow all instructions for mounting the
shade system. Failure to follow these instructions could result in minor to moderate injury.
Align the bracket with the marks or predrilled pilot holes made in the template stage, and fasten
using the mounting screws provided or other fasteners appropriate for the mounting surface.
NOTE: On End and Center brackets, the pre-routed wiring harness should be mounted
facing up (wall mount) or back towards the wall or window (ceiling mount). The mounting
holes in all brackets are elongated to allow for adjustment. Confirm that brackets are level
and aligned (add shims if necessary), and verify the correct bracket-to-bracket distance
before tightening the mounting screws. (For more information about positioning, light gaps,
and final adjustment, please refer to section 5 on page 2. )
End Center
* When concealing the wire housing, the center of the bracket's foot
must be concentric with the housing opening ± ⁄ in (3 mm) without
1
8
interference from the mounting screws
Install Finishing Rings
a. Orient a finishing ring as shown and spread it slightly
to fit it over and around the bracket-shade interface.
The lip on the finishing ring fits in the groove on the
bracket, and the ring will rotate freely when properly
installed.
b. Rotate the finishing ring so that its opening aligns with
the opening in the bracket-shade interface as shown.
c. Repeat steps a. and b. to install a finishing ring on
each bracket.
Care and Maintenance:
After a product has been installed correctly by a qualified installer, there is no mechanical upkeep
required. In the event adjustments or repairs are needed, the original provider of the systems should
be notified. All adjustments and repairs must be made by qualified personnel.
Fabrics can be periodically dusted in place using a feather duster or vacuum with a soft brush
attachment. For detailed fabric care information, refer to www.lutronfabrics.com
FCC / IC INFORMATION
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation.
Modifications not expressly approved by Lutron Electronics Co., Inc. could void the user's authority to operate this equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna
- Increase the separation between the equipment and receiver
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
- Consult the dealer or an experienced radio/TV technician for help
This Class B digital apparatus complies with Canadian ICES-003.
Jamb
Preferred
Orientation
Alternate
Orientation
** When concealing the wire housing,
the housing opening should align
with the wire opening for the jamb
bracket, without interference from
the mounting screws
Lip
Spread
Slightly
Groove
Opening
Rotate