Publicité
Les langues disponibles
Les langues disponibles
EnGLIsh
Filter Cleaning Mechanism
Suction power is dependent on the condition of the filter.
Therefore, the filter should be cleaned regularly.
The filter cleaning mechanism is a feature that uses the motor
in the dust extractor to force air through the filter. Refer
to Emptying the Dust Collection Box for instructions on
proper use.
Emptying the Dust Collection Box (Fig. I, J)
WARNING: The vacuum cleaner contains dust particles
that pose a risk to health. Emptying and maintenance
procedures, including the disposal of dust collectors,
should only be carried out by professionals. Suitable
protective equipment is required. Do not operate the
vacuum cleaner without the complete filter system.
Otherwise you endanger your health.
WARNING: Wear approved eye protection and approved
dust mask when performing this procedure.
CAUTION: Do not clean with water or compressed air.
The dust collection box
should be emptied as soon as the
3
performance has noticeably decreased or is full.
1. Press the dust collection box release buttons
dust collection box away from the dust extraction system.
Once the catch mechanism is clear of the dust extraction
system the upper joint will also release allowing the dust
collection box to be removed completely.
2. To empty the dust collection box
suitable container to catch the dust contained within it.
Lift up the assembly release latch
collection box, separating the canister from the lid. Gently
tapping the dust collection box will encourage any dust
trapped within the filter to also be removed. Once the filter
lid and canister are empty reattach them, ensuring the
assembly release latch
Figure J.
3. To reattach the dust collection box to the dust extraction
system first insert the rounded profile of the upper joint
into the recess on the dust extraction system. Pivot the dust
collection box down so that the release buttons click back
into place. Refer to Figure I.
4. With the dust collection box properly installed, depress the
filter cleaning mechanism
Allow the system to run for 5 seconds and release trigger.
This should be done after every emptying of the dust
collection box.
Transporting the Dust Extractor
WARNING: Accidental start up during transport could
be hazardous. Always transport the dust extractor
with the batteries removed. Refer to the Battery
Packs, Transportation section of this manual for
further information.
WARNING: Check the tool and batteries for damage after
transport and before use.
36
4
and pull the
position it over a
3
18
to open the dust
18
is securely fastened. Refer to
5
and turn on the dust extractor.
Storing the Dust Extractor
WARNING:
a ) Empty the dust collection box before storing the
dust extractor.
b ) Always store your dust extractor with the batteries removed!
c ) Store the tool and batteries in a place that is as cool and
dry as possible.
d ) Store the tool and batteries in a place that cannot be
accessed by children or unauthorised persons.
e ) Check the tool and batteries for damage after long periods
of storage.
f ) Refer to the Battery Packs, Transportation section of
this manual for further information.
MAINTENANCE
WARNING: To reduce the risk of serious personal
injury, turn the dust extractor off and disconnect
battery pack before making any adjustments or
removing/installing attachments or accessories. An
accidental start-up can cause injury.
The charger and battery pack are not serviceable.
nOTE: Cleaning and user maintenance shall not be made by
children.
Replacing the Dust Collection Box Filter
Assembly (Fig. I, J)
WARNING: Wear approved eye protection and approved
dust mask when performing this procedure.
WARNING: Replace any damaged filters immediately.
nOTE: The filter should be replaced after every 350 full to empty
filter box emptying cycles.
1. Press the dust collection box release buttons
dust collection box away from the dust extraction system.
Once the catch mechanism is clear of the dust extraction
system the upper joint will also release allowing the dust
collection box to be removed completely.
2. Discard dust collection box
3. Reattach the dust collection box to the dust extraction
system. First insert the rounded profile of the upper joint
into the recess on the dust extraction system. Pivot the dust
collection box down so that the release buttons click back
into place.
Lubrication
Your dust extractor requires no additional lubrication.
Cleaning
WARNING: Do not use a spray system, pressure jet washer
or running water for cleaning.
and pull the
4
3
replace with a new filter box.
Publicité
