KUNERT BOOSTER Notice D'utilisation page 9

The pram is equipped with a rain cover which is pulled over it. The rain cover has ventilation outlets at the
level of the child's face.
MOUNTING THE CAR SEAT
The pram also comes with a car seat option for children. To mount the car seat, the car seat adapters need
to be mounted first to the chassis. To mount the adapters on the chassis, click them into designated slots
(two on each side of the pram) (fig. 23). WARNING! Before using the car seat, ensure that the car seat
adapters are correctly mounted. Both adapters should be locked. After correct mounting of the car seat
adapters on the chassis, you can move on to mounting the car seat. To mount the car seat, you need to fit
its buckles into matching plastic handles on the adapters (fig. 24).WARNING Before using the pram, make
sure that all locking mechanisms are engaged. This pram does not substitute a cradle or a crib. If
your child needs to sleep, it is recommended to put him/her in an appropriate carrycot, cradle or crib. The
car seat comes with a hood and a cover which are mounted with snaps. The car seat is equipped with an
adjustable handle. The handle is adjusted by pressing the red buttons on both sides of the car seat and
moving the handle into a desired position (fig. 25). To remove the car seat, you need to pull the levers on
both sides of the car seat (fig. 26). To dismantle the adapters, press the buttons on the both sides of the
pram chassis.
HANDLE HEIGHT ADJUSTMENT
To adjust the handle height, you need to press the buttons on both sides of the handle and then adjust the
height while simultaneously pressing the buttons (fig. 27).
MOUNTING AND REMOVAL OF THE CARRYCOT
To mount the carrycot on the chassis, click it into designated slots (one on each side of the pram) (figs 10,
11) until the hooks are locked. The hooks are locked automatically. Warning The carrycot should always be
mounted rear-facing (so that the child faces the person pushing the pram). WARNING Before using the
pram, make sure that all locking mechanisms are engaged (fig. 11). To take the carrycot off, press the
adapter buttons on both sides of the pram (fig. 11) and lift the carrycot up using the handle.
WARNING! Do not fold the pram with the carrycot in it. Warning A child that can sit up on his/her own,
turn over and move on his/her arms and knees should be fastened in a carrycot harness.
WARNING: Do not use a mattress thicker than 10 mm. WARNING: Use the safety harness when your child
starts to sit up on his/her own.
CARRYCOT HOOD
The carrycot has a permanently attached hood. You can adjust the hood as necessary by pressing buttons
on both sides of the hood and positioning the hood as necessary (fig. 12). The hood has a handle which is
used to carry the carrycot (fig. 13).
CARRYCOT COVER
The carrycot is equipped with a cover which can be mounted by attaching the snaps of the cover to the
respective snaps on both sides of the hood (fig. 14).
MOUNTING AND REMOVAL OF THE PRAM SEAT
To mount the seat on the chassis, click it into designated slots (one on each side of the pram) (fig. 15) until
the hooks are locked (fig. 11). The hooks are locked automatically. The stroller seat may be mounted in
front-facing and rear-facing positions. WARNING! Before you use the pram, make sure all blocking devices
are activated. To remove the seat, press the buttons on the both sides of the pram chassis (fig. 11).
WARNING! This seat is not suitable for children under 6 months.
MOUNTLING OF CARRYCOT AND SPORT SEAT AT THE SAME TIME
There I a possibility of mounting a carrycot and a sport seat in the pram at the same time. In this case, we
always assemble the carrycot with the adapters located higher in the rear facing position, while the sport
seat should be mounted in the adapters lower also in the rear facing position.
PRAM SEAT HOOD
The pram seat is equipped with a protective hood. To mount it, slide its hooks into designated slots on
both sides of the pram seat chassis until the hood is locked (fig. 16). To remove the hood, press the buttons
of the hooks on both sides and pull up the hood (fig. 16).The position of the hood is adjustable. It can be
positioned differently. To adjust the hood position, move it forwards or backwards to achieve the desired
result (fig. 17). If a new born baby is put in the stroller, it is recommended to set the position of the seat
which is to be used from the baby's birth in a position similar to a lying one.
BACKREST ADJUSTMENT
The backrest can be adjusted in 4 positions. To lift the backrest up, you need to pull up the lever from
9