Black+Decker BCW201 Mode D'emploi page 9

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

DO nOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start-up can cause injury.
GoPak Tool Terminal Cap
A battery storage and carrying cap
whenever the battery is out of the tool. Remove the cap as
shown in Figure E before placing battery onto tool.
Fig. E
OPERATION

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start-up can cause injury.
Installing and Removing the GoPak 2 in 1
Battery in a Power Tool (Fig. F)

WARNING: Remove any connected USB cords from
the BLACK+DECKER GoPak 2 in 1 battery before
connecting the GoPak to the compatible tool.
1. Remove the tool terminal cap if installed on the
BLACK+DECKER GoPak 2 in 1 battery.
2. To power a compatible GoPak 12V MAX* power tool,
align the tool terminals on the foot of the tool with the
terminal slots on the battery
nOTE: The state of charge indicator will face the rear of
the tool and the USB ports will face the front. The arrow on
the battery will align with the arrow on the tool as shown
in Fig. E.
3. Snap the BLACK+DECKER GoPak 2 in 1 battery into the
foot of the tool. The arrow
with the arrow
on the tool. Ensure the battery is
14
fully seated and fully latched into position before using.
4. To remove the BLACK+DECKER GoPak 2 in 1 battery
from the tool, depress the two battery release buttons
5
located on the tool and pull the BLACK+DECKER
GoPak 2 in 1 battery off the tool.
nOTE: The BLACK+DECKER GoPak 2 in 1 battery USB ports
are disabled when the trigger is pulled.
9
is provided for use
9
as shown in Fig. E.
4
on the battery will align
13
Fig. F
14
13
Using the GoPak 2 in 1 battery to
charge your USB device (Fig. G)
1. Plug the USB A end of your device specific cable
into the BLACK+DECKER GoPak 2 in 1 battery
and the other end of the cable into a UL or CSA listed
compatible device (Phone/Tablet/MP3/Wearable/Game
Controller/etc.). Charging will start automatically.
Fig. G
11
Functionality
The BLACK+DECKER GoPak 2 in 1 battery can power your
compatible BLACK+DECKER 12 V GoPak MAX* tools or
power/charge your mobile devices. The compact, slim
battery housing is designed for portability.
GoPak Charge Input: Up to 2.4A**
-
-
GoPak Power Output: Up to 2.4A***
** Actual input charge rate is dependant upon power
adapter (not included).
***Actual output rate is dependant on the device.
USB Power Port
The BLACK+DECKER GoPak 2 in 1 battery is equipped with a
USB Type A power port. It delivers up to 2.4 amp total current.
nOTE: The current delivered to device is dependent on user
device and user's chosen cable.

WARNING: Ensure the terminal cap is securly
attached to the BLACK+DECKER GoPak 2 in 1 battery
when using it to power/charge your device.
Install terminal cap on the tool terminals.
Device charging from USB will start automatically when
device is connected.
To turn OFF, disconnect USB device.
English
5
4
11
10
10
7

Publicité

Table des Matières
loading

Table des Matières