Page 4
Dear clients, Thank you for having chosen our induction ceramic hob. In order to make the best use of your appliance, we would advise you to read carefully the following notes and to keep them for a later consulting. SUMMARY SAFETY ............................
Page 5
SAFETY Precautions before using • Unpack all the materials. • The installation and connecting of the appliance have to be done by approved specialists. The manufacturer can not be responsible for damage caused by building-in or connecting errors. • To be used, the appliance must be well-equipped and installed in a kitchen unit and an adapted and approved work surface.
Page 6
• Metallic objects such as knives, forks, spoons and lids should not be placed on the hob surface since they can get hot. • In general do not place any metallic object except heating containers on the glass surface. In case of untimely engaging or residual heat, this one may heat, melt or even burn.
Page 7
• If a drawer is situated under the embedded appliance, make sure the space between the content of the drawer and the inferior part of the appliance is large enough (2 cm). This is essential to guaranty a correct ventilation. •...
Page 8
DESCRIPTION OF THE APPLIANCE Technical characteristics Type GTI630BK Total power 4650 W Energy consumption for the hob EC 162.3 Wh/kg Front left heating zone Ø 180 mm Minimum detection Ø 100 mm Nominal power* 1400 W Standardised cookware category** Energy consumption EC...
Page 9
Control panel Timer display [ + ] key [ - ] key Selection Key Control light timer Power display On/off key USE OF THE APPLIANCE Display Display Designation Function Zero The heating zone is activated. 1…9 Power level Selection of the cooking level. Pan detection No pan or inadequate pan.
Page 10
STARTING-UP AND APPLIANCE MANAGEMENT Before the first use Clean your hob with a damp cloth, and then dry the surface thoroughly. Do not use detergent which risks causing blue-tinted colour on the glass surface. Induction principle An induction coil is located under each heating zone. When it is engaged, it produces a variable electromagnetic field which produces inductive currents in the ferromagnetic bottom plate of the pan.
Page 11
Residual heat indication After the switch off of a heating zone or the complete stop of the hob, the heating zones are still hot and indicates [ H ] on the display. The symbol [ H ] disappears when the heating zones may be touched without danger. As far as the residual heat indicators are on light, don’t touch the heating zones and don’t put any heat sensitive object on them.
Page 12
Control panel locking To avoid modifying a setting of cooking zones , in particular with within the framework of cleaning the control panel can be locked (with exception to the On/Off key [ • Locking : Action Control panel Display Start Press key [ [ 0 ] or [ H ]...
Page 13
COOKING ADVICES Pan quality Adapted materials : steel, enamelled steel, cast iron, ferromagnetic stainless-steel, aluminium with ferromagnetic bottom. Not adapted materials : aluminium and stainless-steel without ferromagnetic bottom, cupper, brass, glass, ceramic, porcelain. The manufacturers specify if their products are compatible induction. To check if pans are compatibles : •...
Page 14
Examples of cooking power setting (the values below are indicative) Melting Sauces, butter, chocolate, gelatine 1 to 2 Reheating Dishes prepared beforehand Simmering Rice, pudding, sugar syrup 2 to 3 Defrosting Dried vegetables, fish, frozen products 3 to 4 Steam Vegetables, fish, meat Steamed potatoes, soups, pasta, 4 to 5...
Page 15
WHAT TO DO IN CASE OF A PROBLEM When the symbol [ E 4 ] appears : I) The table must be reconfigured. Please implement the following steps: Important: before you start: • make sure there is no more pot on the hob •...
Page 16
The control panel displays or [ E ] : • Disconnect and replug the hob. • Call the After-sales Service. One or all cooking zone cut-off : • The safety system functioned. • You forgot to cut-off the cooking zone for a long time. •...
Page 17
Width Depth Thick GTI630BK • Ensure that there is a distance of 50 mm between the hob and the wall or sides. • The hobs are classified as “Y” class for heat protection. Ideally the hob should be installed with plenty of space on either side. There may be a wall at the rear and tall units or a wall at one side.
Page 18
ELECTRICAL CONNECTION • The installation of this appliance and the connection to the electrical network should be entrusted only to an electrician perfectly to the fact of the normative regulations and which respects them scrupulously. • Protection against the parts under tension must be ensured after the building-in. •...
Page 19
Chère cliente, cher client, Nous vous remercions de la confiance que vous nous avez accordée en choisissant notre table de cuisson vitrocéramique à induction. Afin de bien connaître cet appareil, nous vous recommandons de lire attentivement cette notice d’utilisation dans son intégralité et de la conserver pour une consultation ultérieure. SOMMAIRE SECURITE ...........................
Page 20
SECURITE Précautions avant utilisation en cuisson • Retirez toutes les parties de l’emballage. • L’installation et le branchement électrique de l’appareil sont à confier à des spécialistes agrées. Le fabricant ne saurait être tenu responsable des dommages résultant d’une erreur d’encastrement ou de raccordement.
Page 21
• Assurez-vous qu’aucun câble électrique d’appareil fixe ou mobile ne vienne en contact avec la vitre ou la casserole chaude. • Les objets magnétisables (cartes de crédits, disquettes informatiques, calculatrices) ne doivent pas se trouver à proximité immédiate de l’appareil en fonction. •...
Page 22
• Eviter que le sucre, les matières synthétiques ou une feuille d’aluminium ne touchent les zones chaudes. Ces substances peuvent au refroidissement provoquer des cassures ou d’autres modifications de la surface vitrocéramique: Eteindre l’appareil et enlevez-les immédiatement de la zone de cuisson encore chaude (attention : risque de brûlures).
Page 23
Autres protections • Assurez-vous que le récipient de cuisson soit toujours centré sur la zone de cuisson. Le fond de la casserole doit autant que possible couvrir la zone de cuisson. • Pour les utilisateurs portant un régulateur de rythme cardiaque, le champ magnétique pourrait influencer son fonctionnement.
Page 24
DESCRIPTION DE L’APPAREIL Caractéristiques techniques Type GTI630BK Puissance Totale 4650 W Consommation d’énergie de la table de cuisson EC 162.3 Wh/kg Foyer avant gauche Ø 180 mm Détection minimum Ø 100 mm Puissance nominale* 1400 W Catégorie de la casserole standard** Consommation d’énergie EC...
Page 25
Bandeau de commande Affichage minuterie Touche [ - ] Touche [ + ] Touche sélection Affichage Touche Voyant sélection minuterie puissance Marche/Arrêt UTILISATION DE L’APPAREIL Affichage Affichage Désignation Fonction Zéro La zone de chauffe est activée. 1…9 Niveau de puissance Choix du niveau de cuisson.
Page 26
MISE EN ROUTE ET GESTION DE L’APPAREIL Avant la première utilisation Nettoyez votre appareil avec un chiffon humide, puis séchez-le. N’utilisez pas de détergent qui risquerait de provoquer une coloration bleutée sur les surfaces vitrées. Principe de l’induction Une bobine d’induction se trouve sous chaque foyer de cuisson. Lorsque celle-ci est enclenchée, elle produit un champ électromagnétique variable qui, à...
Page 27
Détection de récipient La détection de récipient assure une sécurité parfaite. L’induction ne fonctionne pas : • Lorsqu’il n’y a pas de récipient sur la zone de cuisson ou lorsque ce récipient est inadapté à l’induction. Dans ce cas il est impossible d’augmenter la puissance et dans l’afficheur le symbole [ U ] apparaît.
Page 28
• Minuterie utilisée hors cuisson : Action Bandeau de commande Afficheur Activer la table de cuisson appuyer sur [ voyants de zone allumes Sélectionner « Minuterie » appuyer simultanément [ 00 ] sur [ - ] et [ + ] Diminuer la durée Appuyer sur [ - ] [00] passe à...
Page 29
CONSEILS DE CUISSON Qualité des casseroles Matériaux adaptés : acier, acier émaillé, fonte, inox à fond ferro-magnétique, aluminium à fond ferro-magnétique. Matériaux non adaptés : aluminium et inox à fond non ferro-magnétique, cuivre, laiton, verre, céramique, porcelaine. Les fabricants spécifient si leurs produits sont compatibles induction. Pour vérifier si des casseroles sont compatibles : •...
Page 30
Exemples de réglage des puissances de cuisson (Les valeurs ci-dessous sont indicatives) Faire fondre Sauces, beurre, chocolat, gélatine 1 à 2 Réchauffer Plats pré-cuisinés Gonfler Riz, pudding et plats cuisinés 2 à 3 Décongélation Légumes, poisson, produits congelés 3 à 4 Vapeur Légumes, poissons, viande Pommes de terre à...
Page 31
QUE FAIRE EN CAS DE PROBLEME Le symbole [ E 4 ] s’affiche : I) La table doit être reconfigurée suivant la procédure ci-dessous : • Avant de commencer la procédure, il faut : • S’assurer qu’il n’y ait pas de récipients sur la table à induction. •...
Page 32
Le symbole [ E ] s’affiche : • d’ébranchez et rebranchez la table de cuisson • appelez le Service Après-ventes L’une des zones ou l’ensemble du plan de cuisson se déclenche : • le déclenchement de sécurité a fonctionné • celui-ci s’actionne dans le cas ou vous avez oublié de couper une des zones de chauffe •...
Page 33
Larg. Prof. GTI630BK • La distance entre la table de cuisson et le mur doit être au minimum de 50mm. • La table de cuisson est un appareil qui appartient à la classe de protection « Y ». Lors de son encastrement, une paroi d’armoire haute ou un mur peut se trouver sur l’un des côtés...
Page 34
CONNEXION ELECTRIQUE • L’installation de cet appareil et son branchement au réseau électrique ne doit être confiés qu’à un électricien parfaitement au fait des prescriptions normatives. • La protection contre les pièces sous tension doit être assurée après le montage. •...