Table des Matières
Publicité
DBG 150 PLUS | DBG 200 PRO
service and use only original spare parts. This will
ensure that the safety of the power tool is main-
tained.
BENCH GRINDER SAFETY wARNINGS
Do not use a damaged accessory. Before each
f
use, inspect the accessory such as abrasive
wheels for chips and cracks. After inspecting
and installing an accessory, position yourself
and bystanders away from the plane of the ro-
tating accessory and run the power tool at max-
imum no-load speed for one minute. damaged
accessories will normally break apart during this
test time.
The rated speed of the accessory must be at
f
least equal to the maximum speed marked on
the power tool. accessories running faster than
their rated speed can break and fly apart.
Never grind on the sides of a grinding wheel.
f
Grinding on the side can cause the wheel to break
and fly apart.
wear safety goggles.
f
Never leave the tool unattended before it has
f
come to a complete stop. cutting tools that are
still running can cause injuries.
Store the power tool and accessories safely
f
when it is not in use. The storage location must
be dry and lockable. This prevents the power tool
from storage damage, and from being operated by
untrained persons.
Check the cable regularly and have a damaged
f
cable repaired only by an authorised custom-
er service agent for FF Group power tools.
Replace damaged extension cables. This will
ensure that the safety of the power tool is main-
tained.
Connect the tool to a mains supply that is prop-
f
erly connected to earth. The socket and exten-
sion cable must have a fully functioning protective
conductor.
keep your work area clean. Material mixtures are
f
particularly hazardous. light metal dust may catch
fire or explode.
Protect the grinding tool against impact, shock
f
and grease.
PRODUCT SPECIFICATIONS
INTENDED USE
The power tool is intended for sharpening tools
and for grinding and deburring metal. The power
tool may only be operated for short periods (max.
60 mins).
TECHNICAL DATA
Article number
Model - DBG
Rated power
input
Power output
operating mode
45 523
45 525
150 PLUS
200 PRO
w
400
500
w
250
310
S2 (10min)
no load Speed
min
voltage/
v/hz
Frequency
dry wheel size
mm
left
Grit
dry wheel size
mm
Right
Grit
weight
Sound emission values determined according
to EN 62841-1, EN 62841-3-4
Typically the a-weighted noise levels of the product
are:
Sound pressure
db(a)
level
Sound power
db(a)
level
Uncertainty K
db
* The operating mode S2 (60 mins) indicates short-
term operation with a maximum operating time of
60 minutes. after this time put down the power
tool and let it cool down.
The specifications apply to a rated voltage [U] of
230 v. These specifications may vary at different
voltages and in country-specific models.
wEAR HEARING PROTECTION
The noise emission value given in these instruc-
tions has been measured in accordance with a
standardised measuring procedure and may be
used to compare power tools. It may also be used
for a preliminary estimation of noise emissions.
The noise emission value given represents the
main applications of the power tool. however, if
the power tool is used for other applications, with
different application tools or is poorly maintained,
the noise emission value may differ. This may sig-
nificantly increase noise emissions over the total
working period.
To estimate noise emissions accurately, the times
when the tool is switched off, or when it is running
but not actually being used, should also be taken
into account. This may significantly reduce noise
emissions over the total working period.
IDENTIFICATION
1. Spark arrestor
2. holder for the spark arrestor
3. Grinding wheel (right 60 grit, left 36 grit)
4. workpiece support
5. lEd work lamp
6. Protective guard
7. Mounting holes
8. On/off switch
9. clamping nut
10. Grinding spindle
11. Clamping flange
12. Mounting flange
English |
2.980
-1
230/50
150 x 20
200 x 20
x 12,7
x 15,88
#
36
60
150 x 20
200 x 40
x 12,7
x 15,88
#
60
100
kg
8,2
13,0
84,3
85,3
91,1
91,8
3,0
www.ffgroup-tools.com
9
Publicité
Table des Matières
