Publicité
A
Please read
these
instructions carefully before you start to
assemble this
product
and carry
out the
steps
in
the order
set
out
in
these instructions.
iWhen
encountering the information
icon, please refer
to the relevant
assembly step for additional comments and
assistance.
Care
and Safety Advice
For
safety purposes we
strongly recommend the product to
be
assembled
by at least
two
people.
Some parts may have sharp edges. Please be careful when
handling
components.
Always wear gloves,
eye
protection,
and long sleeves when
assembling or performing any maintenance
on
your product.
Do
not attempt to
assemble the
product
in
windy
or
wet conditions.
Dispose
of
all
plastic
bags safely
-
keep
them out of
reach
of
small
children.
Keep
children away from the assembly
area.
Do
not attempt to
assemble the
product if
you
are
tired,
have
taken drugs,
medications
or alcohol, or if you are prone to dizzy spells.
When using
a
stepladder
or
power tools,
make sure you
follow
the
manufacturer's safety advice.
Do
not climb
or stand
on
the
roof.
Heavy articles should
not
be
leaned against the poles.
Do
not
hang or
lay on
the profiles.
Keep
roof and gutter
clear
of
snow,
dirt
& leaves.
Heavy
snow load
on
roof
can
damage the
product making it
unsafe
to
stand
below
or nearby.
Keep these
instructions
in
a
safe
place
for future
reference.
If color
was scratched
during assembly it
can be
fixed
with the following tints:
White
-
RAL
9016
Cleaning Instructions
When
your product
needs cleaning,
use
a
mild detergent solution
and rinse
with
cold
clean water.
Do
not
use
acetone, abrasive cleaners, or others special detergents to clean
the
panels.
Before Assembly
This
product must
be
assembled on
a
solid, level
base
/
surface
(such
as
concrete or asphalt) and anchored to the ground.
Choose
your
site
carefully before beginning
assembly.
Sort the parts and check according
to the contents
parts
list.
Please
consult your
local
authorities if any permits
are
required prior to
constructing the product.
Tools &
Equipment
T001
(Supplied)
Notes
During Assembly
When
encountering
these icons, you
are
requested to either
keep
the
screws
slightly
loose or
to fully tighten the
screws.
Steps
Step 8:
Please
apply
silicone sealants above beam
7288
+
7290,
in
order to prevent water from
seeping
in
(drawing
b).
Step 12:
Please
note the profile's direction (8063), the
canal
should
be on
the internal
side.
Step 13: Make
sure
that the angle between the
back wall
profile
and the panel
supporting
profiles
is
90 degrees.
Step 23:
Please
apply
silicone sealants
to the inner
edges
of
parts
7043 & 7042
as
well
as
to the
middle
of
parts
7029
+
7039
in
order to prevent water from seeping
in.
Step 24:
Please
apply
silicone sealants on
the inner part of 7027 & 7028, and connect to the
profile
as
depicted
in
drawing
b.
Step 28: Important!
Please
make sure
the frame
is
perfectly centered before fixing.
Step 31:
Please
do not cut profile 8055
unless needed.
Step 33:
Please
loosen the screws
as
shown
in
diagram
c,
set
the
beam exactly on
top of
the
poles, once
done
re-
tighten the
screws.
Step 37:
Please
do not cut profile 8056
unless needed.
Step 38:
Please
do
not cut profile 8057
unless needed.
Please
do
not cut the Acrylic
sheets 8111
& 8113
unless needed, all
precautions must
be taken.
Step 52: Optional! Part 8115
sets
the grey marked
doors, thus creating smaller openings.
*Tighten
all screws
when completing
assembly.
Please
note:
Anchoring this product to the ground
is
essential
to
its
stability
and
rigidity, and
required
in
order for your warranty to
be
valid.
The
wall anchoring kit supplied with this
product
is
suitable only for concrete
walls.
Other wall types
need
an
accordant wall fixation
kit. (Contact
your supplier)
N
0
Ln
J
Publicité
