HIKVISION DS-3E1310HP-EI Guide De Démarrage Rapide page 4

●
The equipment must be connected to an earthed mains socket-outlet. (This is for Class I equipment only.)
●
Shock hazard! Disconnect all power sources before maintenance if the equipment adopts multiple power supply.
●
The socket-outlet shall be installed near the equipment and shall be easily accessible.
●
Ensure correct wiring of the terminals for connection to an AC mains supply if the equipment is suitable for non-standard socket-outlet.
●
indicates hazardous live and the external wiring connected to the terminals requires installation by an instructed person.
●
The equipment has been designed, when required, modified for connection to an IT power distribution system.
●
This equipment is not suitable for use in locations where children are likely to be present.
●
Install the equipment according to the instructions in this manual. To prevent injury, this equipment must be securely attached to the DIN rail, wall or rack in accordance
with the installation instructions. Never place the equipment in an unstable location. The equipment may fall, causing serious personal injury or death.
●
This equipment is suitable for mounting on concrete or other non-combustible surface only.
●
Keep body parts away from fan blades if the equipment has a fan. Disconnect the power source during servicing.
●
Keep a minimum 10 cm distance around the equipment for sufficient ventilation. The ventilation should not be impeded by covering the ventilation openings with items,
such as newspapers, table-cloths, curtains, etc. The openings shall never be blocked by placing the equipment on a bed, sofa, rug or other similar surface.
●
Burned fingers when handling the housing parts. Wait one-half hour after switching off before handling the parts.
●
No naked flame sources, such as lighted candles, should be placed on the equipment.
●
The equipment shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the equipment.
●
CAUTION: This equipment is for use only with its supporting bracket. Use with other (carts, stands, or carriers) may result in instability causing injury. This bracket is
intended for use only with the equipment. Use with other equipment may result in instability causing injury.
●
CLASS 1 LASER PRODUCT
Appearance
The following table is for your reference only.
Indicator/Port Description
●
PoE-MAX Indicator
●
●
PWR Indicator
●
LINK/ACT Indicator
●
●
SFP Port Indicator
●
●
PoE Indicator
●
PoE Port Used for connection to PDs with network cables.
Hi-PoE Port Used for connection to Hi-PoE PTZ cameras. At different temperatures, the max. power of the ports is different.
RJ45 Port Used for connection to devices with network cables.
SFP Port Used for connection to device with an optical fiber when plugged into with an optical module.
●
●
Combo
●
●
DIP Switch ●
●
Solid on/Blinking: The output power of the switch is about to reach or already reaches the upper limit. The
power supply may be abnormal if more devices are connected.
Unlit: The switch provides power to a powered device (PD) normally.
Solid on: The switch is powered on normally.
Unlit: No power supply connected or power supply is abnormal.
Solid on: The port is connected.
Blinking: The port is transmitting data.
Unlit: The port is disconnected or connection is abnormal.
Solid on: The switch provides power to a PD normally.
Unlit: The switch is disconnected from the PD, or provides power to the PD abnormally.
When connected to a network cable, the combo functions as a RJ45 port.
When plugged into with an optical module and connected to an optical fiber, the combo functions as
a fiber optic port.
When connected to the network cable and optical fiber at the same time, the combo works as a fiber optic
port.
Extend: The ports support network transmission of up to 300 m.
Isolation: Data transmission of each port is isolated from each other to improve network security.
PoE Watchdog: Auto-detect and restart cameras that do not respond.
2
English