Test Mode - Urmet 1051/201 Guide Rapide

TAMPER
This protects from attempts to removal or opening of the casing. When the tamper switch is open, the contact sends an alarm signal
to the control unit and the LED is lit.

TEST MODE

The contact can be set to Test mode for 3 minutes by pressing the Test button on the front cover once. The LED lights up when ever
the contact is activated in Test mode. Whenever the Test button is pressed, the contact transmits a signal to the control unit to test the
wireless range and re-activates Test mode again for three minutes. Test mode will end automatically after 3 minutes and will return to
normal operating mode.
LEARNING PROCEDURE
Step 1: Remove the battery insulation.
Step 2: Start the learning function on the control unit; see the control unit manual for more information.
Step 3: Press the Test button on the contact to send a signal to the control unit.
Step 4: If the control unit receives the signal correctly will respond by emitting beeps. Refer to the manual of the control unit to
complete the learning process.
Step 5: After the contact has been learnt, set the control unit to "Walk Test" mode, by holding the contact in the desired position and
press the Test button to check that it is within the wireless range of the control unit.
Step 6: After having checked the correct position of contact, proceed with the installation.
INSTALLATION
Step 1: Install the contact using one of the methods described below.
Step 2: Install the magnet on the part with the most movement (such as a door) using the screws
supplied (double-sided tape is provided only if drilling is not possible).
Align the magnet with the indicators of the contact.
If necessary, use the magnet spacer to correctly align it with the indicators.
< N O T E >
< N O T E >

With the door closed, the magnet must be at a distance of less than 15 mm from the
detector.
There are two ways to install the contact: with double-sided adhesive tape or with screws.
Installation with double-sided adhesive tape (exceptional cases only)
I. Clean the surface using a suitable degreaser.
II. According to the installation side, remove the protective film from one of the sides of
the double-sided tape and make it adhere firmly to the back of the device.
III. Remove the other protective film and make it adhere tightly to the contact in the
desired position.
< N O T E >
< N O T E >

Do not use the installation method with double-sided adhesive tape on surfaces with peeling or cracked
paint or on uneven surfaces.

Install the contact on the part which does not move (as the frame of a door or a window) and
install the magnet on the moving object (such as the door or the window). Carefully check that
the rubber cap mounted on the tamper switch is still in place.
Installation with screws
The base is provided with knockouts where the plastic is thinner to allow installation.
To fit the contact:
I. Remove the cover by undoing the retaining screws.
II. Break the areas provided on the base.
III. Using a template for the holes, make the holes in the wall.
IV. Insert the anchor bolts if the device is fixed to plaster or bricks.
V. Screw the base into the anchor bolts.
VI. Secure the cover to the base and tighten the cover fixing screws. Carefully check that
the rubber cap mounted on the tamper switch is still in place.
Hereby, URMET S.p.A. declares that the radio equipment type: WHITE OR BROWN MINI MAGNETIC CONTACT 1051/201 and
1051/202 are in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following
internet address: www.urmet.com.
LINK TO ACCESS THE PRODUCT TECHNICAL SHEET AND DOWNLOAD THE COMPLETE MANUAL
DIRECTIVE 2012/19/EU OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 4 July 2012 on waste electrical and
electronic equipment (WEEE). The symbol of the crossed-out wheeled bin on the product or on its packaging indicates that
this product must not be disposed of with your other household waste. Instead, it is your responsibility to dispose of your
waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic
equipment. The separate collection and recycling of your waste equipment at the time of disposal will help to conserve
natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more
information about where you can drop off your waste equipment for recycling, please contact your local city office, your household
waste disposal service or the shop where you purchased the product.
4
SIMPLIFIED EU DECLARATION OF CONFORMITY
DS1051-025