Lincoln Electric MOBIFLEX 300-E Manuel Opérateur page 17

Symptom Problem
Dust or smoke Pollution of the
coming out of facility.
the filter cover.
Machine Machine does
makes a not function
sputtering properly.
noise.
Vibrations in Machine not
the machine. steady.
8 SPARE PARTS
The following spare parts are available for the machine (refer to
exploded view Fig. I on page 49).
Article no. Description
Mobiflex 300-E general
0000101885 Ionisation wire for FIS (10 pcs)
0050101240 Hose set LFA for mounting on mobile unit
0101050010 Ioniser FIS
0102080030 Aluminium pre/final filter SAF
0104060010 Activated carbon final filter SCF
0302250010 Capacitor 0,5 μF, 660V
0324150120 Control lamp 28V, yellow
0326000520 PC board HT
0328100020 Safety switch, 2 poles
0328410130 Relay MC2A
0334100200 Transformer 50W/24V 115/230/400V
0340000110 Fuse 2,0 A
0609590110 Starlock 22 mm
0612010220 Adjusting ring 19x1
0708020140 Aluminium fan wheel 50Hz
0708020150 Aluminium fan wheel 60Hz
0801400010 Housing SF 1400/2400/M.100-NF/mobile units, motor
side
0803010080 Insulator FCS
0803011090 Insulator FIS
0805030010 Wheel Ø 250 mm black
0805040010 Swivel castor Ø 125 mm with brake
0805040050 Swivel castor Ø 125 mm without brake
0806014020 Cover star knob M8
0840101030 Bush Ø 203 mm
9821430000 Collector FCS
0507250020/010513/F Mobiflex 300-E
Possible cause Solution
Ioniser and/or Clean the filters and
collector mount them
saturated or correctly. Ref. 6.2
mounted and 6.2.4.
incorrectly.
High voltage Replace high voltage
transformer transformer.
defective.
High voltage PC Replace high voltage
board defective. PC board.
Short-circuit in Check and repair.
the ioniser and/
or collector.
Bad contact in Check and repair.
the ioniser and/
or collector.
Ioniser and/or Mount the filters
collector correctly. Ref. 6.2.4.
mounted
incorrectly.
Ioniser and/or Clean the filters. Ref.
collector 6.2.
seriously
polluted.
Not properly Let the filters dry
dried ioniser thoroughly after
and/or collector. cleaning.
Broken Replace ionisation
ionisation wires wires.
in the ioniser.
Bent lamelles in Straighten lamellas.
the collector. Ref. 6.2.3.
Metal particles in Remove metal
ioniser and/or particles and clean
collector. the filters.
Imbalance in the Clean the extraction
extraction fan. fan.
Article no. Description
9821430010 HT transformer Mobiflex 300-E
9824000070 Filter cover M.200-M/300-E incl. outlet grid
9824000110 Mounting set safety switch Mobiflex 300-E
9824000210 Axle
9850040080 Wheel covers red M.200-M/400-MS/300-E (2 pieces)
Mobiflex 300-E 400V/3ph/50Hz
0320000100 Motor 0,75kW, 230-400V/3ph/50Hz
0328260080 Motor protection switch MPS 1.6-2.5A
Mobiflex 300-E 230/3ph/50Hz
0320000100 Motor 0,75kW, 230-400V/3ph/50Hz
0328260090 Motor protection switch MPS 2.5-4.0A
Mobiflex 300-E 230/1ph/50Hz
0321012030 Motor 0,75kW, 115-230V/1ph/50-60Hz
0328260100 Motor protection switch MPS 4.0-6.3A
Mobiflex 300-E 115/1ph/50Hz
0321012030 Motor 0,75kW, 115-230V/1ph/50-60Hz
0328260200 Motor protection switch MPS 10-16A (CSA+UL)
9 ELECTRICAL DIAGRAM
Refer to the separately supplied electrical diagram.
10 DISPOSAL
After life of the machine, dispose it of in accordance with
federal, state or local regulations.
CE DECLARATION
EC declaration of conformity for machinery
(according to Annex II A of the Machinery Directive)
We, Plymovent, Wezelkoog 11, 1822 BL Alkmaar, the
Netherlands, herewith declare, on our own responsibility, that
the machinery:
- Mobiflex 300-E
which this declaration refers to, is/are in accordance with the
conditions of the following Directives:
- Machine Directive 2006/42 EC
- EMC 2004/108 EC
- LVD 2006/95 EC
and is/are in conformity with the following harmonized
standard(s) and/or other such normative documents +
amendments, if any:
- EN ISO 12100-1:2003 (safety of machinery)
- EN ISO 12100-2:2003 (safety of machinery)
- EN ISO 13857:2008 (safety distances)
- EN-IEC 60335-1
- EN-IEC 60335-2-65
Alkmaar, the Netherlands, May 1, 2013
Ir. F. Coehoorn
Vice President Research & Development
EN - 16