Publicité
Les langues disponibles
Les langues disponibles
Recoil with choke, speed lever illustration F3-C*
1.
By cold engine set the choke lever on "Choke".
By warm engine set the choke lever on "Run".
2.
Hold the handlebar for the engine brake; this will
release the engine brake.
3.
Pull the recoil starter gently until you feel resistance
in the rope, then pull quickly and energetic. Do not
at any time let go of the recoil starter but slide it
gently into starting position.
4.
Return the choke lever in the "Run" position (only
cold engine) .
5.
Set speed lever in gear from 1 to 4 (C)
6.
Hold the bar for self-propelled in order to start
mowing.
* Note: Not all models are equipped with choke lever.
Note: As long as operating the mower, the bar
forengine brake must be engaged.
Throttle lever*
Engine speed can be adjusted while driving. Turn gas
handle to adjust rpm. (ID: M) It is recommended to run
at full throttle for best cutting results.
* Note: Not all models have throttle control
Regulation of speed*
Speed can be adjusted from 2.7 – 5.0 km/h while
driving. Activate the right handle on the dashboard and
set in one of the 4 different speeds. When driving in one
the two lowest speeds the pace difference will not vary
significantly.
Change the speed only while the machine is operating
with the self-propelled function engaged.
This ensures a minimum of wear on the drive belt and
ensures an easy speed change.
If the drive speed is changed when the machine is not
moving, there is a risk that the belt will fall off as soon
as the machine starts to move. In addition, there is a
risk that the cable and the belt may become damaged.
* Note: Not all models have speed lever
Stop: Illustration F4
1.
Release the engine brake and self-propelled bar to
turn off the mower and the engine
Note: The blades will still rotate at up to 3 seconds
after stopping.
Fixation of front wheel: Illustration F5
The front wheels can be pivotally, which gives a good
maneuverability, when cutting around flower beds, trees
etc. The direction of the front wheels can also be fixed,
so that it only points forward. Change of postion is done
by pulling the lock and turn it into a new position and
then releasd the lock again, so it falls into position.
Water nozzle
The left side of the mower deck is fitted with a water
nozzle for washing the deck. (See Illustration ID-F)
•
When using the water nozzle, the machine must be
in the lowest height position and placed on the
lawn. This ensures that the water remains under
the deck during cleaning.
•
Attach a hose to the nozzle.
•
Turn on the water and start the engine.
•
The rotations of the blades will ensure that the
water will clean the underside of the deck.
If above instruction is not followed, water may
splash back on the gearbox and clutch cable,
which increases the risk of corrosion and damage
to both parts. This will not be covered by the
warranty!
Note: For best result clean the deck with the water
nozzle function right after each mowing. If the grass
dries out, this function will not work optimally.
* Note: Not all models have water nozzle
Oil change
Oil should be changed for the first time after 5 hours,
then at least 1 time per year.
You will need an oil extractor kit. Art. no. 40-11336
Oil and oil extractor kit is not included
Use an extractor kit and do as follows:
1.
Turn on the engine and let it run for 5 min or until
the engine is hot. A hot engine liquefies the oil
which makes it easier to drain.
2.
Suck the oil up through the oil filler hole using the
syringe that came with the oil extractor kit. Use the
hose to reach the sump.
3.
Transfer the used oil into a empty container.
4.
Fill the engine with SAE-30 oil.
5.
Check the oil level using the dipstick. (Min / Max)
Remember to dispose the used oil so that it does
no harm to nature. Use your local recycling station.
Air Filter
The air filter should be inspected and cleaned regularly.
If the filter has not been cleaned for a long time, the
engine's power will drop.
See Illustration A2
1.
Clean around the air filter before removing the cap.
2.
Push the two flaps down and gently pull the cover
3.
Carefully remove the paper filter and inspect it.
Brush it with a soft brush. If it is very dirty, replace
it. Be careful that no dirt gets into the inlet.
4.
Wash the black foam element in the right side in
warm water and soap.
5.
Press the water out of the foam element and let it
dry. Put a few drops of SAE-30 oil on the filter to
moisten it lightly. Carefully squeeze any surplus oil
out of the foam element and reattach.
6.
Please note that all parts are assembled correctly
and properly closed, as shown in the picture.
Blade
Inspection of the blade
•
Tilt the mower with the front upwards.
•
Inspect blade for damage, cracks or excessive rust
or corrosion.
•
Check that the blade bolt is tightened.
Note: A dull blade can be sharpened! But a blade that
is worn, bent, cracked or otherwise damaged must be
replaced.
Removing the blade: See illustration A3
If you remove the blade to sharpen or replace it, you
must use a torque wrench and some heavy gloves to
protect your hands.
1.
Loosen the blade bolt. Use a piece of wood to
prevent the blade from turning around.
9
Publicité
