Ryobi RLS02 Traduction Des Instructions Originales page 3

GENERAL SAFETY WARNINGS
WARNING
Safe operation of this accessory requires that you read
and understand this operator's manual, the operator's
manual for the table saw and all labels affi xed to the tool.
■
Know your accessory. Read the operator's manual
carefully. Learn its applications and limitations, as
well as the specific potential hazards related to this
accessory.
■
Keep the work area clean. Cluttered work areas and
work benches invite accidents.
■
Always wear safety glasses with side shields.
Everyday glasses have only impact resistant lenses.
They are NOT safety glasses.
■
This stand will accommodate many mitre saws.
However, it should never be used on any mitre saw
or slide mitre saws with a blade diameter larger
than 305mm. Always confirm any mitre saw used is
mounted securely and is stable before plugging in the
mitre saw. Before turning on the saw, perform a dry
run of the cutting operation just to make sure that no
problems will occur when the cut is made.
■
This stand is designed to be used on a flat stable
surface. Do not use the stand on an uneven or unstable
surface. Be sure to allow enough room to handle and
properly support the workpiece.
■
Follow the tool mounting instructions carefully, and
ensure the tool is fastened securely.
■
Maximum weight of the mitre saw and workpiece
together must not exceed 181kg.
■
Do not apply an unbalanced load that could cause
the mitre saw stand to tip over.
■
Save these instructions. Refer to them frequently and
use them to instruct others who may use this accessory.
If you loan someone this accessory, loan them these
instructions also to prevent misuse of the product and
possible injury.
■
This stand is designed for use with mitre saws or
slide mitre saws with a blade diameter not larger
than 305mm.
■
If any parts are missing do not operate this tool
until the missing parts are replaced. Failure to do so
could result in possible serious personal injury.
■
Do not attempt to modify this tool or create
accessories not recommended for use with this
tool. Any such alteration or modification is misuse
and could result in a hazardous condition leading to
possible serious personal injury.
■
Do not connect to power supply until assembly is
complete. Failure to comply could result in accidental
starting and possible serious personal injury.
■
To avoid serious personal injury, make sure the
curved front edge of the mounting brackets are
securely seated over the front rail before seating
the other end of the brackets. Failure to do so
could cause you to lose control of the saw mounting
assembly, which could cause serious personal injury.
■
The mounting brackets are designed to fit snugly
over the stand rails. With the locking levers in the
lowered (locked) position, you should not be able to
remove the saw and bracket assembly from the rails.
If the mounting brackets will not fit over the rails, or if
the mounting brackets can be removed from the rails
when the levers are locked, remove from the saw and
bracket assembly immediately and tighten the bracket
adjustment screw as described in the Maintenance
section of this manual. Failure to heed this warning may
result in serious personal injury.
■
Do not allow familiarity with tools to make you
careless. Remember that a careless fraction of a
second is sufficient to inflict serious injury.
■
Do not use any attachments or accessories not
recommended by the manufacturer of this tool. The
use of attachments or accessories not recommended
can result in serious personal injury.
■
When servicing, use
replacement parts. Use of any other parts may create
a hazard or cause product damage.
■
Do not at any time let brake fluids, gasoline,
petroleumbased products, penetrating oils, etc.,
come in contact with plastic parts. Chemicals can
damage, weaken or destroy plastic which may result in
serious personal injury.
SYMBOL
Wear eye protection
Avoid contact with any pinch point
English
only identical Ryobi
1
EN
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
EL
TR