Publicité
Les langues disponibles
Les langues disponibles
English
the possibility of kickback. Please refer to the table below to
determine the correct wheel for your application.
Wheel type
Diamond** Multi‑Material
Wheel
Bonded Reinforced Wheel
Diamond** Tile Wheel
**This blade uses manufactured diamonds engineered
for cutting.
nOTE: Bonded Reinforced wheels are composed of abrasive
grains which are held tightly together by a bonding agent
and typically reinforced with a woven material.
Installing/Replacing Wheels
(Fig. A, F1, F2, L, M)
WARNING: Burn Hazard. Sharp parts. ALWAYS wear
gloves when changing wheels. Wheels have sharp
edges or may get extremely hot during operation, and
may damage bare hands.
WARNING: To reduce the risk of injury, only use wheels
that are no greater than 3" (76 mm) in diameter, have
an inner diameter of 3/8" (or 7/16" if using adapter
ring), and without cutting teeth. Thickness of wheel not
to exceed 0.09" (2.2 mm). Never force a wheel onto the
machine or alter the size of the arbor hole.
WARNING: Since accessories, other than those
offered by CRAFTSMAN , have not been tested with
this product, use of such accessories with this tool
could be hazardous. To reduce the risk of injury, only
CRAFTSMAN recommended accessories should be
used with this product.
WARNING: Failure to properly seat the flanges and/
or wheel could result in serious injury (or damage to the
tool or wheel).
1. Remove the battery.
2. Lay unit on a firm surface, with the spindle
facing upward.
3. Hold spindle lock button
from turning. Spindle threads are left hand.
4. Using supplied 6 mm hex wrench
to remove spindle screw
wheel
if one is installed. Leave inner flange
18
in place.
nOTE: Hex wrench is magnetically secured.
nOTE: It is possible that the inner flange and outer
flange may stick together. Be sure to keep both flanges
seperated during the wheel installation process. Refer
to Fig. F2 showing the correct order of the flanges and
wheel installed over the spindle.
5. Ensure inner flange is installed over the spindle.
nOTE: Your tool comes provided with a 7/16" arbor
adapter
17
which should only be used when installing
a 7/16" wheel. The 7/16" arbor adapter is not to be used
with the wheels provided with this tool. When installing
7/16" wheels, place the 7/16" arbor adaptor over the
inner flange. The 7/16" arbor adapter will fit inside the
12
Application
Drywall, fiber cement, plastic, steel, non
ferrous materials
Steel, stainless steel, non‑ferrous materials
Ceramic Tile, Porcelain and Granite/Marble/
Stone
15
6
to keep the spindle
, rotate clockwise
12
, outer flange
, and used
20
19
center of the 7/16" wheel when assembled. Refer to
Fig. F1.
6. Slip wheel over spindle. Make sure wheel goes over pilot
diameter of inner flange.
nOTE: When installing diamond wheels, always match
direction of rotation of the wheel to the desired direction
of rotation of the tool.
7. Slip on outer flange with the flat side towards the wheel.
nOTE: The text "LOOSEN TIGHTEN" will be visible when
installed correctly.
8. Start threading on spindle screw counterclockwise which
will self align outer flange. Make sure the wheel is fitted
in the correct orientation.
9. Depress and hold spindle lock button and tighten
spindle screw with hex wrench. Do not overtighten
spindle screw.
10. Release spindle lock button and turn wheel by hand to
ensure it is properly centered. The wheel should not hit
the shoe, guard or spindle screw. The spindle screw and
flanges should be tight.
nOTE: Do not run tool with the spindle lock engaged.
Always allow motor to come to a complete stop before
engaging the spindle lock.
Adjusting the Rotatable Guard Angle (Fig. G)
WARNING: Remove battery first. To reduce the risk
of injury, ALWAYS adjust the guard to provide the
best control and protection. ALWAYS wear gloves to
protect your hands when adjusting the guard as the
guard may get hot.
WARNING: Adjust the position of the guard to provide
the maximum protection from loose particles and
sparks thrown from the wheel.
CAUTION: Guard must be used with all cutting wheels.
1. Remove the battery.
2. Grasp the rotatable guard
snaps securely into one of three positions.
Mounting, Removing the Shoe (Fig. A, J1)
Your cut off tool comes pre-assembled with the shoe
mounted to the rotatable guard
To Remove the Shoe
16
1. Remove the battery pack
2. Loosen the depth adjustment knob
3. Remove the depth adjustment knob and remove shoe
from the rotatable guard.
To Mount the Shoe
1. Remove the battery pack.
2. Install shoe onto the back of the rotatable guard, aligning
slot
29
3. Install and rotate the depth adjustment knob clockwise
to tighten.
nOTE: The shoe is not required for use with this tool. For
best performance the shoe is recommended for more
stability when cutting on a flat surface.
firmly and rotate until it
11
11
.
1
.
to threaded hole
25
on guard. Refer to Fig. J1.
9
10
counterclockwise.
Publicité
