Publicité
Les langues disponibles
Les langues disponibles
Operating Instructions
Installation
Operation
Warning
Trouble Shooting Aurora Paper Shredders
Maintenance
Limited Warranty
Manuel de fonctionnement
Installation
Fonctionnement
Avertissement
Dépannage des déchiquteuses
à papier Aurora
Entretien
Garantie limitée
Instrucciones para operar
Instalaciones
Operación
Avertencia
Solucionar Problemas de la Máquina
Trituradora de Documentos Aurora
Mantenimiento
Garantía Limitada
Please read these operating instructions before using the unit.
Customer Service: 1 - 800 - 327 - 8508 or INFO@AURORACORP.COM
Avant d'utiliser cet appareil, Veuillez lire toutes les instructions.
Service à la clientèle : 1 - 800 - 327 - 8508 OU INFO@AURORACORP.COM
Antes de operar esta unida, por favor lea todas las instrucciones.
Servicio al Consumidor: 1 - 800 - 327 - 8508 O INFO@AURORACORP.COM
1
4 sheets of
Sheet Capacity
20lb. bond paper
Credit Card Capacity
1 at a time
7/32" x 1 27/32" pieces
Paper Shred Size
0.56 cm x 4.7 cm pieces
Voltage
120V-60Hz 1.2A
Capacité de passage
4 feuilles de papier
à la fois
bond de 75g/m2 (20lb.)
Capacité les cartes de crédit
les introduire un par un
en morceaux de 7/32" x 1 27/32"
Dimensions des déchets
en morceaux de 0.56 cm x 4.7 cm
Tension
120V-60Hz 1.2A
Capacidad de
4 hojas de papel de
destruccióna la vez
cartes de 20 libras
Capacidad de
introdúzcalos en la ranura
tarjetas de crédito
uno por uno
en pedazos de 7/32" x 1 27/32"
Tomaño de corte
en pedazos de 0.56 cm x 4.7 cm
Voltaje
120V-60Hz 1.2A
( U.S.A. ONLY )
( ETATS-UNIS SEULEMENT )
( LOS ESTADOS UNIDOS SÓLO )
INSTALLATION :
Mount the shredder securely to the rim of the waste basket. (FIGURE 1)
Connect the power cord to any standard 120 volt AC outlet. (FIGURE 2)
Note: Crosscut shredders includes a built in safety mechanism that requires the shredder to be correctly
mounted on the supplied wastebasket. Lining the wastebasket with a plastic bag will interfere
and may keep the shredder from functioning.
Caution: Crosscut shredders have very sharp, exposed blades on the underside.
Use care when mounting the shredder on the wastebasket.
FIGURE 1
OPERATION :
Using the switch located on the unit, select one of the following settings by sliding the switch either left or
right. (FIGURE 3)
I
Auto: This setting allows the shredder to be automatically started by inserting paper into the
shred opening. Always feed the paper in as straight as possible. When the paper has
passed through, the shredder will stop. (FIGURE 3)
O
Off: This setting turns off all features of the shredder. For safety reasons, we recommend that
you leave the shredder in the Off position whenever the shredder is unattended or not in use.
(FIGURE 3)
R
Rev: In the unlikely event of a paper jam, the reverse setting can be used to help clear the
cutters of paper that has not passed through. Never attempt to clear a jam by using
the reverse function until you have emptied the wastebasket. (FIGURE 3)
Note: Never continuously run this shredder for more than 10 minutes.
In the event that the shredder is run continuously for too long and the motor overheats, a
thermal overload switch will automatically shut the power off. If this happens, move the switch
to the off position for 20 minutes or more before continuing.
Never shred plastic, continuous forms, anything with adhesive including labels and envelopes, newsprint,
or any hard materials. While this shredder will shred staples, it is recommended that you remove them
whenever possible in order to extend the life of your shredder.
Only shred credit cards by feeding them vertically within the designated area.
Never feed more than one credit card at a time.
FIGURE 2
FIGURE 3
2
Publicité
