Ryobi RY28160 Manuel D'utilisation page 14

 Squeeze the throttle trigger fully and pull the starter handle
until the engine runs. Do not pull the starter grip more
than six (6) times.
NOTE: Keep throttle trigger squeezed fully through re-
maining steps. If the engine does not start, start over at
the first step with pressing the primer bulb.
 Allow the engine to run for 10 seconds, then set the choke
lever to the RUN (B) position.
To restart a warm engine:
 Slowly press the primer bulb 10 times.
 Set the choke lever to the RUN (B) position.
 Squeeze the throttle trigger fully and pull the starter handle
until the engine runs.
To stop the engine:
 To stop the engine, depress the STOP switch to the stop
position " ".
IF ASSISTANCE IS REQUIRED FOR THIS PRODUCT:
Do not return this product to the retail store where it was
purchased. Please call our Customer Service Department
for any issues you may have.
For Help Call: 1-800-860-4050
OPERATING THE BRUSH CUTTER
See Figure 15.
WARNING:
Engine housing can become hot during operation. Do
not rest or place your arm, hand, or any body part against
the engine housing during operation. Only hold the unit
as shown in Figure 15 during brush cutter and Figure 17
for during trimmer operation with all body parts clear of
engine housing (or as shown in the applicable attachment
Operator's Manual). Extended contact with the engine
housing can result in burns or other injuries.
WARNING:
Always position the unit on the operator's right side. The
use of the unit on the operator's left side will expose the
user to hot surfaces and can result in possible burn injury.
WARNING:
To avoid burns from hot surfaces, never operate unit with
the bottom of the engine above waist level.
Hold the brush cutter with your right hand on the rear handle
and the your left hand on the J-handle. Keep a firm grip with
both hands while in operation. Brush cutter should be held at
a comfortable position with the rear handle about hip height.
Maintain your grip and balance on both feet. Position yourself
so that you will not be drawn off balance by the kickback
reaction of the cutting blade.
OPERATION
Adjust the shoulder harness to position the brush cutter
at a comfortable operating position and to assure that the
shoulder harness will reduce the risk of operator contact
with the blade.
WARNING:
Always hold the brush cutter away from the body keeping
clearance between the body and the product. Any contact
with the housing can result in burns and/or other serious
personal injury.
BLADE THRUST
Exercise extreme caution when using the blade with this
unit. Blade thrust is the reaction that may occur when the
spinning blade contacts anything it cannot cut. This contact
may cause the blade to stop for an instant, and suddenly
"thrust" the unit away from the object that was hit. This re-
action can be violent enough to cause the operator to lose
control of the unit. Blade thrust can occur without warning
if the blade snags, stalls, or binds. This is more likely to oc-
cur in areas where it is difficult to see the material being cut.
For cutting ease and safety, approach the weeds being cut
with the brush cutter from the right to the left. In the event
an unexpected object or woody stock is encountered, this
practice could minimize the blade thrust reaction.
TRI-ARC
The Tri-Arc
stalks. When the blade becomes dull, it can be turned over
to extend the life of the blade. Do not sharpen the Tri-Arc
blade.
CUTTING TECHNIQUE - BLADE
See Figure 16.
WARNING:
Extreme care must be taken when using blades to ensure
safe operation. Read the safety information for safe op-
eration using the blade, refer to Specific Safety Rules
for Brush Cutter and Blade Use earlier in this manual.
 Always hold brush cutter on your right side with both
hands when operating. Use a firm grip on both handles.
 Maintain your grip and balance on both feet. Position
yourself so that you will not be drawn off balance by the
kickback reaction of the cutting blade.
 Inspect and clear the area of any hidden objects such as
glass, rocks, concrete, fencing, wire, wood, metal, etc.
 Never use blades near sidewalks, fencing, posts, build-
ings or other immovable objects.
 Never use a blade after hitting a hard object without first in-
specting it for damage. Do not use if any damage is detected.
 The unit is used as a scythe, cutting from the right to the
left in a broad sweeping action from side to side.
10 — English
BLADE
®
blade is suited only for thicker weeds and pulpy
®
®