KLEIN+HUMMEL O 810 Mode D'emploi page 22

Bass Management Bass Management Bass Management Bass Management
In order to maintain a high-quality signal path, there is no VOL stage on the SUM OUTPUT so daisy-chained
subwoofers must be individually controlled. The cables required for this depend on the source of the control data.
If the control equipment has RS-232 on D-sub connectors, an RS
and 5 should be connected. Pins 4 and 5 should be crossed over, i.e. TX connects to RX and vice versa. An adapter
can be self-made (see picture below) or ordered from Klein + Hummel (RS232
Options section.
If the control equipment has a USB connector, a USB to RS
section. It is not recommended to use commercially available adapter as, depending on the internal wiring,
damage is possible. Once the USB is converted to RS-232, an RS
the subwoofer – see Accessories and Options section.
For multiple subwoofer systems, an EtherCon Adapter
Four EtherCon sockets allow for simultaneous connection of a hardware remote control and an RS-232 source –
although simultaneous adjustment of the hardware remote should be avoided when sending data from the RS-
232 source. The last subwoofer in the daisy-chain is connected directed to the to previous subwoofer's SEA 1 Sub
Out socket. The connectors are for:
1. Hardware remote input (SRC 1 or SRC 2)
2. RS-232 input / Subwoofer daisy chain input
3. Subwoofer slave output (subwoofer 2, 3, ...)
4. Subwoofer output
K+H SEA 1
EtherCon Adapter
SRC n RS -232
/ Sub in
From SRC 1 or SCR 2
From RS-232 Device
O 810 / O 870 Operating Manual
All manuals and user guides at all-guides.com
Subwoofer Subwo Subwo Subwo ofer ofer ofer
ON ON
ON MUTED
DISABLE ON
DISABLE MUTED
9 5
6 1
D D D D - - - - Sub Pin Sub Pin CAT- - - - 5 5 5 5 Pin CAT
Sub Pin Sub Pin CAT CAT
2 (RX)
3 (TX)
5 (GND)
Do not connect shield
RS RS- - - - 232 D 232 D- - - - Sub to CAT Sub to CAT- - - - 5 Adapter
RS RS 232 D 232 D Sub to CAT Sub to CAT
USB to RS- - - - 232 Adapter
USB to RS USB to RS
EtherCon Adapter (SEA 1) is required – see Accessories and Options section.
EtherCon Adapter EtherCon Adapter
SUBWOOFER 1
Remote Control
and RS-232 Input
Slave Sub SRC n RS-232
Out Out
Page 22 of 96
Bass Extension ( Bass Extension ( Bass Extension (- - - - 3 dB) Bass Extension ( 3 dB) 3 dB) 3 dB)
18 Hz
80 Hz
Main Loudspeaker's LF Cut-off
Main Loudspeaker's LF Cut-off
RS- - - - 232 to CAT 232 to CAT- - - - 5 5 5 5 cable is required. Only pins 3, 4
RS RS 232 to CAT 232 to CAT
RS232- - - - to to to to- - - - CAT5 CAT5) – see Accessories and
RS232 RS232 CAT5 CAT5
1
8
Pin
Pin Pin
4 (TX)
5 (RX)
3 (GND)
5 Adapter
5 Adapter 5 Adapter
232 Adapter is required – see Accessories and Options
232 Adapter 232 Adapter
RS RS RS- - - - 232 to CAT 232 to CAT 232 to CAT- - - - 5 Adapter 232 to CAT 5 Adapter is required to connect to 5 Adapter 5 Adapter
SUBWOOFER 2, 3, ...
Remote Control Remote Control
and RS-232 Input and RS -232 Input
K+H SEA 1
EtherCon Adapter
Slave Sub
/ Sub in Out Out
Klein + Hummel
SUBWOOFER n
Version 01