RedMax 322HD60 Manuel D'utilisation page 17

Any part repaired or replaced under the warranty must
be warranted for the remaining warranty period.
DIAGNOSIS: You will not be charged for diagnostic
labor that leads to the determination that a warranted
part is in fact defective, provided that such diagnostic
work is performed at a brand authorized servicing
dealer.
OTHER DAMAGES: Husqvarna Professional Products,
Inc. will repair other engine components caused by the
failure of a warranted part still under warranty.
EMISSION WARRANTY PARTS LIST
1. Carburetor and intake parts or fuel injection system.
2. Air filter and fuel filter covered up to maintenance
schedule.
3. Spark Plug, covered up to maintenance schedule.
4. Ignition Module.
5. Mufflers with catalyst and exhaust manifolds.
6. Fuel tank, fuel lines (for liquid fuel and fuel vapors),
fuel cap, carbon canister and tip-over/anti-slosh
valves as applicable.**
7. Electronic Controls, Vacuum, temperature, and time
sensitive valves and switches.
8. Hoses, connectors, and assemblies.
9. All other components the failure of which would
increase the engine's exhaust and evaporative
emissions of any regulated pollutant as set forth at
the following:
• For California see California Code of
Regulations, 13 CCR §2405(d) and 2760(d).
• For U.S. and Canada see US Federal Code of
Regulations, 40 C.F.R 1068 Appendix I (iii).
WHAT IS NOT COVERED
All failures caused by abuse, neglect, unapproved
modifications, misuse or improper maintenance are not
covered.
ADD -ON OR MODIFIED PARTS: Add-on or modified
parts that are not exempted by CARB or EPA may
not be used. The use of any non-exempted add-on or
modified parts will be grounds for disallowing a warranty
claim. Husqvarna Professional Products, Inc. will not be
liable to warrant failures of warranted parts caused by
the use of a non-exempted add-on or modified part.
HOW TO FILE A CLAIM
If you have any questions regarding your warranty
rights and responsibilities, you should contact your
nearest authorized servicing dealer or call Husqvarna
Professional Products, Inc. in USA at 1-800-487-5951,
in CANADA at 1-800-805-5523 or send e-mail
correspondence to emissions@husqvarnagroup.com or
warranty@hpp-emissions.com.
WHERE TO GET WARRANTY SERVICE
Warranty services or repairs are provided through
all Husqvarna Professional Products, Inc. authorized
servicing dealers. If the nearest authorized servicing
1073 - 008 - 27.04.2023
dealer is more than 100 miles from your location,
Husqvarna Professional Products, Inc. will arrange
and pay for the shipping costs to and from a
brand authorized servicing dealer or otherwise arrange
for warranty service in accordance with applicable
regulations.
MAINTENANCE, REPLACEMENT AND REPAIR OF
EMISSION-RELATED PARTS
Any replacement part may be used in the performance
of any warranty maintenance or repairs and must be
provided without charge to the owner. Such use will not
reduce the warranty obligations of the manufacturer.
MAINTENANCE STATEMENT
The owner is responsible for the performance of all
required maintenance, as defined in the operator's
manual.
* Current and following model year will be updated
annually in the warranty statement provided to the
consumer. For example, in 2012 model year, 2012-2013
will be specified.
** Evaporative emission parts.
AMERICAN STANDARD SAFETY
PRECAUTIONS
SAFETY PRECAUTIONS FOR CHAIN SAW USERS
( Annex )
KICKBACK SAFETY PRECAUTIONS
WARNING:
the nose or tip of the guide bar touches
an object, or when the wood closes in and
pinches the saw chain in the cut.
Tip contact in some cases may cause a
lightning fast reverse reaction, kicking the
guide bar up and back towards the operator.
Pinching the saw chain along the top of the
guide bar may push the guide bar rapidly
back towards the operator.
Either of these reactions may cause you to
lose control of the saw which could result in
serious personal injury.
Do not rely exclusively upon the safety
devices built into your saw. As a chain saw
user, you should take several steps to keep
your cutting jobs free from accident or injury.
With a basic understanding of kickback, you can reduce
or eliminate the element of surprise. Sudden surprise
contributes to accidents.
Keep a good firm grip on the saw with both hands, the
right hand on the rear handle, and the left hand on the
front handle, when the engine is running. Use a firm
grip with thumbs and fingers encircling the chain saw
Kickback may occur when
17