Publicité
Les langues disponibles
Les langues disponibles
PREPARATION FOR USE
CONNECTIONS
Plug the incoming cable into the ANT jack on the rear of the TV.
Cable
Antenna
OR
TV signal
Incoming cable from home antenna /
cable company (No cable box)
Cable box or
Satellite box*
OR
OU T
IN
Incoming cable from cable
company or satellite antenna
Cables not included
You can bracket this product as wall mounting TV using the arm adapted for 100mm (commer-
cially available).
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO
WIDE SLOT, FULLY INSERT.
Note:
•
For your safety and to avoid damages to the unit, unplug the antenna cable from the
ANT jack before moving the unit.
[EXTERNAL CONNECTION]
VIDEO1 input
(OUT)
ex.
Audio Cable
(OUT)
Video Cable
Video Cassette
OR
(OUT)
Recorder
S-Video Cable
Notes:
The AUDIO L jack is for mono input. The sound is heard from both speakers. Use this jack for
●
connecting monaural audio equipment.
The S-VIDEO jack is given priority over the VIDEO jack.
●
VIDEO2 input
ex.
(OUT)
Audio Cable
Video Camera
(OUT)
Component
Video Game
Video Cable
Notes:
This TV can accept 480p / 480i / simplified 1080i video signal.
●
Simplified 1080 video signal differs to the original 1080i video signal because it is displayed
●
after converted into 480p signal.
INSTALLING THE BATTERIES
1
2
3
[BATTERY PRECAUTIONS]
• Be sure to follow the correct polarity as indicated in the battery compartment.
Reversed batteries may cause damage to the device.
• Do not mix different types of batteries together (e.g. Alkaline and Carbon-Zinc) or old batteries
with fresh ones.
• If the device is not to be used for a long period of time, remove the batteries to prevent
damage or injury from possible battery leakage.
• Do not try to recharge batteries not intended to be recharged; they can overheat and rupture.
All manuals and user guides at all-guides.com
Rear of this TV
AN T
*NOTE (DO NOT DISCONNECT FROM BOX)
Some cable TV systems use scrambled signals
and require a special converter to receive these
channels. Consult your local cable company.
Rear of this TV
(IN)
(IN)
(IN)
(IN)
Rear of this TV
(IN)
Install two AAA batteries (supplied)
matching the polarity indicated inside
battery compartment of the remote con-
trol.
INITIAL SETUP
When you turn on the power for the first time, the "SELECT LANGUAGE" menu is displayed.
The "INITIAL SETUP" menu is displayed every time you turn on the unit unless the scanning is completed.
1
1
Select the desired
SELECT LANGUAGE
language according to
ENGLISH
NEXT:PRESS CHK
the screen indication.
ESPAÑOL
DESPUÉS:PRESIONE CHL
FRANÇAIS
APRÈS:PRESSEZ VOLX
After that, the TV
performs "AUTO
PRESET CH" to scan
– INITIAL SETUP –
channels available for
PLEASE CONNECT ANTENNA OR CABLE
OR SATELLITE TO THIS UNIT.
the broadcasting in
THEN PRESS CH K,
IN ORDER TO PERFORM
your area.
"AUTO PRESET CH ".
When the scanning is completed, or [MENU] is pressed during channel scanning to cancel it, the
tuner stops on the lowest memorized channel.
Notes:
In case no channel can be received by the channel scanning, "NO TV SIGNALS" is displayed on
●
the screen. Turn off the unit and check the antenna connection, then follow step 1 again.
If those settings do not work properly, please call our help line on the front page of this owner's manual.
●
SELECTING AUDIO/VIDEO INPUT
When you use the AUDIO/VIDEO input jacks, select "VIDEO1" or "VIDEO2" mode by
pressing [INPUT SELECT] on the remote control or [SELECT] on the main unit. The input
mode changes by pressing the button as following:
INPUT
TV channel
SELECT
PHOTO STAND
PHOTO STAND
Photo Stand
Adjust the length of the stand in 5 levels
to change the angle of the TV.
OPERATIONS
REMOTE CONTROL AND FRONT PANEL FUNCTION
IR transmitter
To send infrared ray (IR) signal
POWER button
To turn TV on/off
VOL
X X
/
Y Y
buttons
To adjust volume
To decide the command of settings
MENU button
To view on-screen menu
MUTE button
To mute sound
DISPLAY button
To display CH No./Audio Status
Note:
You can test if the remote control sends out the infrared signal with an AM radio.
●
(Refer to "TROUBLESHOOTING GUIDE".)
L CHANNEL K SELECT POWER
MENU
Y VOLUME X
MENU
Y VOLUME X
L CHANNEL K
VOLUME X X / Y Y buttons
To adjust volume
MENU button
To view on-screen menu
Infrared Sensor Window
Note:
If some digits appear in the corner of the screen when the unit is turned on for the first time,
●
press [POWER] without unplugging the power cord.
2
2
If the TV screen shows
1. PLEASE CHECK TO SEE IF THE
snow noise and there is
2. DID YOU PERFORM "AUTO PRESET CH" ?
no operation for more
3. PLEASE REFER TO FRONT PAGE OF THE
than 5 seconds,
"HELPFUL HINTS"
appears. Follow the
instructions listed on-
screen.
VIDEO1
VIDEO2
INPUT SELECT button
INPUT
SELECT
To select TV or external input
POWER
K K
L L
CH
/
buttons
o
CH
To select channels and move
m
p
up/down through menu items
VOL
n
Channel number buttons
1
2
3
Press two digits to directly access the
desired channel. Remember to press
4
5
6
a "0" before a single digit channel.
+100 button
7
8
9
Press to select cable channels
higher than 99.
0
+100
MENU
SLEEP button
To set Sleep Timer
MUTE
SLEEP
CH RET
DISPLAY
CH RET button
To return to previous channel
SELECT POWER
POWER button
To turn TV on/off
SELECT button
To select TV or external input
CHANNEL K K / L L buttons
To select channels
- HELPFUL HINTS -
ANTENNA/CABLE/SATELLITE IS
PROPERLY CONNECTED.
OWNER'S MANUAL OR REAR PANEL FOR
SUPPORT LINE INFORMATION.
Publicité
