Sanyo DC-UB1475M Manuel D'instructions page 11

BEFORE OPERATION
This instruction manual explains the various functions of this unit
using the remote control. The buttons on the main unit perform
similar functions to similary marked buttons on the remote control.
Turning the power on and off
Press the z/STANDBY button to turn on the power, the display lights up
and "HELLO" appears briefl y.
To turn the power off, press the z/STANDBY button again. "Good bye"
appears briefl y, then the clock display remains lit dimly.
- When the mains lead is connected to the AC outlet, the unit will re-
spond to commands from the remote controller.
Adjusting the volume
Press the VOLUME + or - button. The volume level appears by numbers
(VOL MIN ~ VOL MAX) on the display.
Dynamic Bass Boost System
Press the DBBS button to enhance the bass sound. "BBS ON" appears
on the display.
Press the button again, "BBS OFF" appears. Normal sound resumes.
Selecting the sound mode (Remote control only)
Press the SOUND button to select the sound mode matching the music
to be listened to.
CLASSIC: Classical music, etc.
ROCK: Rock music, etc.
POP: Pops, etc.
JAZZ: Jazz, etc.
FLAT: Normal
Selecting the mute mode (Remote control only)
Press the MUTE button once. "MUTE" blinks on the display, the sound
is mute.
Press the button again, "MUTE" disappear. Normal sound resumes.
WHAT TO DO IF ...
If the operation of the unit or display is not normal,
1. Press the z/STANDBY button to turn off the power.
2. Turn on the power and resume the operation.
All manuals and user guides at all-guides.com
10
CD PLAY
Use compact discs bearing the symbol shown in Fig. 8. In addition to
conventional 12 cm CDs, this system can be used to play 8 cm CDs
without an adapter.
1. Press the FUNCTION button to select "CD" function.
2. Press the CD compartment lid (OPEN/CLOSE q portion) to open it,
"OPEN" appears.
3. Place the disc with the label facing up on the disc turntable (Fig. 9).
(Place only one disc at a time.)
4. Press the CD compartment lid (OPEN/CLOSE q portion) again
to close it. "READING" blinks for several seconds, then the total
number of tracks and total playing time appear.
Note:
If a badly scratched disc is loaded or if the disc is loaded with the
label facing downward, "NO DISC" appears. If this occurs, load the
disc correctly or replace the damaged disc.
5. Press the i button. Play starts from the fi rst track.
The current track number and elapsed playing time are displayed.
6. Press the n button to end disc play.
When the last track has been played, the player stops automatically.
Notes on handling compact discs
- Do not expose the disc to direct sunlight, high humidity or high
temperatures for extended periods of time.
- Discs should be returned to their cases after use.
- Do not apply paper or write anything on the disc surface.
- Handle the disc by its edge. Do not touch the playing surface (glossy
side).
- Fingerprints and dust should be carefully wiped off the playing
surface of the disc with a soft cloth.
Wipe in a straight motion from the centre to the outside of the disc.
- Never use chemicals such as record cleaning sprays, antistatic
sprays or fl uids, benzene or thinner to clean compact discs.
To start play from the desired track
Select the track by using the e or f button, then press the i
button.
Temporarily stopping play
Press the i button, elapsed playing time blinks on the display. To
resume play, press the button again.
Skip play
To skip to track 6 while track 3 is playing, press the e button
repeatedly until "06" appears (in the track section) on the display. To skip
back to track 3 while track 6 is playing, press the f button repeatedly
until "03" appears.
- The number buttons on the remote control can also be used for skip
play. To skip to track 6 while one track is playing, press 0, then 6.
Search (forward/reverse)
If the e or f button is pressed during play, the player will search at
high speed in the forward or reverse direction while the button is being
pressed. When the button is released, normal play will continue.