AmazonBasics B08PCYSRDW Manuel De L'utilisateur page 6

7.4 Status indicators
OVERHEAT: The product has exceeded its maximum
operating temperature and stopped. Stop using the
product without switching it off to allow the fan
to accelerate the cooling process. Wait for at least
10 minutes to cool down before resuming normal
operation.
OVERLOAD: Too much paper has been inserted into
the paper/card feed slot (J). The product goes into a
"Reverse" mode automatically to withdraw the paper.
Pull out manually the batch of paper and reduce the
number of sheets.
BINFULL: The bin (I) is full. Set the on/off switch (C)
to O and unplug the product before emptying the
bin (I).
DOOR OPEN: The bin (I) is not installed properly.
Remove, empty and install the bin (I) correctly in
place. This product features a safety power cut-off
and does not operate if the bin (I) is not in place.
8. Cleaning and Maintenance
W ARNING
Risk of electric shock!
» To prevent electric shock, unplug the product before
cleaning.
» During cleaning do not immerse the electrical parts of the
product in water or other liquids. Never hold the product
under running water.
W ARNING
Risk of fire or explosion!
» Do not spray or keep any aerosol products in or around the
product.
8.1 Cleaning
» To clean the product, wipe with a soft, slightly moist cloth.
» Wipe the product dry after cleaning.
» Never use corrosive detergents, wire brushes, abrasive
scourers, metal or sharp utensils to clean the product.
9. Troubleshooting
Problem
The product does not switch on.
For UK only: Fuse in the plug is blown.
The motor is constantly operating while in
AUTO mode.
The feed slot is jammed.
8.2 Oiling procedure
NOTICE
to oil the product once a month. Otherwise the product may
experience diminished shredding capacity, intrusive noise
when shredding and could ultimately stop operating.
1. Press the
indicator goes off.
2. Drizzle some oil on a few sheets of paper and feed those
pages through the paper/card feed slot (J).
3. Activate the reverse mode for 3–5 seconds.
W ARNING
» Do not use aerosol or pressurized products.
8.3 Storage
» Store the product in its original packaging in a dry area. Keep
away from children and pets.
8.4 Plug fuse replacement (for UK only)
» Use a flat screwdriver to open the fuse compartment cover.
» Remove the fuse and replace with the same type (5 A,
BS1362). Refit the cover.
8.5 Maintenance
» Any other servicing than mentioned in this manual should be
performed by a professional repair centre.
Solution
» Check if the plug is connected to the socket‑outlet. Use voltage tester to verify if
the socket‑outlet is powered.
» Check if the on/off switch (C) is set to I.
» Motor overheated due to extended operation longer than 20 minutes. Stop using
the product for at least 20 minutes to cool down.
» Remove, empty and refit the bin (I) in place properly.
» The sensor of the product is located near the center of the feed slot (K, J). Feed
directly into the center area to activate the motor, especially for smaller pieces of
paper or credit cards.
Follow steps in chapter "Plug fuse replacement" to change the fuse.
Press the button to exit AUTO mode and clean the sensors located near the center
of both feed slots with a dry cotton swab.
» Press the button to exit AUTO mode. Press the
material.
» Spread and loosen the paper with a thicker piece of paper. Press the
shred the paper again.
» For situations where the
jammed paper with shredder oil. Drizzle some oil into the paper/card feed slot (J)
where the paper is jammed. Let it soak for about 30 minutes and repeat the
procedure.
Use only dedicated shredder oil (not provided)
button to switch off the AUTO mode. The blue
Risk of explosion!
button to eject the jammed
button or the button does not help, loosen the
EN
button to
5