Hasbro NERF PRO GELFIRE MYTHIC Mode D'emploi page 2

1 . CHARGING BATTERY
REMOVE BATTERY
Squeeze tabs and slide battery out of blaster.
1
1
2
CHARGE BATTERY
2
Using a USB-A to USB-C
HOURS
connector cable, insert the
USB-C end into battery
charger port.
Attach the cable to a
USB-A wall charger (not
included).
It takes approximately 2
hours to fully charge the
battery.
• Light is steady when
charging.
• Light shuts off when
battery is fully charged.
• Flashing light: Charging
issue. Unplug and replug
charging cord, and try
charging again.
Store the battery outside of / separate from the blaster.
For peak performance, fully charge battery before each
battle. Recharge when rate of fire noticeably declines.
INSERT BATTERY
Squeeze tabs and slide battery into blaster.
1
1 2
2. HYDRATE ROUNDS
Open 1 packet and pour rounds
into container of clean tap water. It
x1 is recommended to use at least 0.5
7.4V
500mAh
gallon/2 liters of water per 5,000 rounds.
If you want to hydrate only some of
the rounds in a packet and save some
Includes rechargeable
rounds for later, use the same amount
7.4V 500mAh LiPo
of water. More water than recommended
battery. Replaceable.
will not impact hydration: It is not
possible to overhydrate the rounds
or grow them too large to function in
IMPORTANT: RECHARGEABLE the blaster. Make sure rounds are fully
submerged in water.
BATTERY INFORMATION
Retain this information for future
reference. Batteries should be
replaced by an adult.
WARNING :
Risk of fire, explosion, and burns. Do
not disassemble, crush, heat above
ROUND
45 °C (113 °F), or incinerate. Dispose
STORAGE
of this battery according to your
HOURS
local recycling or waste regulations
Discard any
unused hydrated
– never disassemble. Do not use the
rounds.
item near a heat source such as a
fire or heater.
BLASTER STORAGE
CAUTION :
Risk of fire and burns. Do not
1. Store the battery outside
open, crush, heat above 45˚C, or
of / separate from the
incinerate. Follow manufacturer' s blaster.
instructions.
WARNING :
Use only with the device provided.
1
Chargers used with the product
are to be regularly examined for
1
damage to the cord, plug, enclosure
and other parts, and that, in the
event of such damage, the product 2
must not be used with this charger
until the damage has been repaired.
NOTE: The battery terminals are not
to be short-circuted.
3. ATTACH HOPPER
Remove cap from hopper and hold it with opening facing
up. Fill hopper with hydrated rounds.
Drain ALL water from hopper.
Holding blaster upside down, twist hopper onto blaster
with a 1/4 turn to lock it in place. Make sure hopper is
securely attached. Turn blaster right side up.
Allow rounds
to remain in
container
for about 3-4
hours to be
fully hydrated.
HOURS
2. Make sure trigger lock is 3. Prior to storage, clean the blaster of
in locked position when any Nerf Pro Gelfire round residue that
storing the blaster. remains in the hopper feed or the barrel.
Use a long soft and clean item, such as
a cotton swab, to clear debris. Clean only
with a damp cloth or a soft, clean, dry item.
4. FIRE
Wear the included protective eyewear
when you or anyone else nearby is
using a Nerf Pro Gelfire blaster.
Unlock trigger.
Turn selector to desired mode:
Semi-auto:
Fires a round per trigger pull.
Selector Light
Flashing
Full-auto:
Fires continuously while trigger is depressed.
Selector Light
Steady
Selector Light
Off
NOTE: Always turn selector to OFF
when not in use.