Publicité
Les langues disponibles
Les langues disponibles
_{ _<_( ',_t_
@_,
_/'_ _C__'_ '_
TO turn the ice maker on/off:
The OH/OFF switch is located on the top right side of the freezer
compartment.
1. To turn the ice maker on, slide the control to the ON (left)
position.
NOTE: Your ice maker has an automatic shut-off. The ice
maker sensors will automatically
stop ice production,
but the
control will remain in the ON (left) position.
2. To manually turn the ice maker off, slide the control to the
OFF (right) position.
To remove and replace ice bucket:
1.
Place four fingers in bucket base opening and rest thumb on
the release button.
2.
Holding the base of the bucket with both hands, depress the
release button and lift the bucket up and out. It is not
necessary to turn the ice maker control to the OFF (right)
position. The ice maker will not produce ice without the
bucket installed in the door.
Accelerated
Ice Production
This feature assists with temporary periods of heavy ice usage by
increasing ice production
over a 24-hour period.
•
Press the accelerated
ice production
touch pad to set the
freezer temperature to -10°F (-23°C). The refrigerator
temperature
will not change. The accelerated
ice setting will
remain on for 24 hours unless manually turned off.
If increased ice production
is desired at all times, set the
Freezer Control to a colder setting. Adjusting the freezer to a
colder temperature
may make some foods, such as ice
cream, harder.
REFRIGERATOR
FEATURES
Your model may have some or all of these features. Features that
can be purchased separately as product accessories are labeled
with the word "Accessory."
Not all accessories will fit all models.
If you are interested in purchasing one of the accessories,
please
call the toll-free number on the cover or in the "Accessories"
section.
Important information to know about glass shelves
and covers:
Do not clean glass shelves or covers with warm water when
they are cold. Shelves and covers may break if exposed to
sudden temperature
changes or impact, such as bumping.
For your protection,
tempered glass is designed to shatter
into many small, pebble-size pieces. This is normal. Glass
shelves and covers are heavy. Use special care when re-
moving them to avoid impact from dropping.
To care for ice storage bucket:
1.
Empty the ice bucket. Use warm water to melt the ice if
necessary. Never use anything
sharp to break up the ice in
the bucket. This can cause damage to the ice container and
the dispenser mechanism.
2. Wash ice bucket with a mild detergent, rinse well and dry
thoroughly.
Do not use harsh or abrasive cleaners or solvents.
REMEMBER:
•
Allow 24 hours to produce the first batch of ice.
•
Discard the first three batches of ice produced to avoid
impurities that may be flushed out of the system.
•
The quality of your ice will be only as good as the quality of
the water supplied to your ice maker.
Avoid connecting the ice maker to a softened water supply.
Water softener chemicals (such as salt) can damage parts of
the ice maker and lead to poor quality ice. If a softened water
supply cannot be avoided, make sure the water softener is
operating properly and is well maintained.
•
it is normal for the ice cubes to be attached at the corners.
They will break apart easily.
•
Do not store anything in the ice maker or ice bucket.
Your model may have glass or wire shelves. Store similar foods
together and adjust the shelves to fit different heights. This
reduces the time the refrigerator door is open and saves energy.
Slide-out
Shelves (on some models)
To remove and replace a shelf in a metal frame:
1.
Pull the shelf forward to the stop. Tilt the front of the shelf up
and lift it slightly as you pull the shelf from the frame.
2.
Replace the shelf by guiding it back into the slots on the
frame and pushing the shelf in past the stop.
14
Publicité
