Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
BUILT-IN TRIM KIT INSTALLATION INSTRUCTION
FOR WHIRLPOOL TRIM-KIT MODELS: MK1197XH, MK1190XH
• FOR USE WITH WHIRLPOOL MICROWAVE OVEN MODELS : MT1195SG, GT1196SH,
GT1195SH, MT3185SH, 89990, 89999, 89998, (Y)KCMS185J, MT2210SJ
•
UL LISTED - FOR USE OVER ELECTRIC HEAT SOURCE
(INCLUDING MODELS - 27": (Y)RBS275PD, (Y)GBS277PD, KEBI171D, (Y)KEBS177D
PARTS LIST
CUTOUT DIMENSIONS
27 "
Height
16
1 /2
Width
25
" 25
Depth
21
"
with flush mount receptacle.
3 /4
(min.)
(22
"
used)
All manuals and user guides at all-guides.com
(KEEP FOR FURTHER REFERENCE)
- 30": (Y)RBS305PD, GBS307PD, (Y)KEBI101D, (Y)KEBS107D)
Trim Kit
Bottom Duct (1)
Side Duct (1)
30 "
3 /4
"
1 /2
1 /2
"
(min.),
28
"
if non-flush receptacle is
(max.)
1" Screws
(4 Req'd 2 Extra)
1/2" Screws
(11 Req'd 2 Extra)
Anti-Tip
Bracket (1)
Bottom
Bracket (1)
Upper Duct (1)
Template (1)
Depth
Width
P/NO.: 3828W5U0085/8172239
Height
3" Min.
Publicité
Manuels Connexes pour Whirlpool MK1197XH
Sommaire des Matières pour Whirlpool MK1197XH
- Page 1 BUILT-IN TRIM KIT INSTALLATION INSTRUCTION (KEEP FOR FURTHER REFERENCE) FOR WHIRLPOOL TRIM-KIT MODELS: MK1197XH, MK1190XH • FOR USE WITH WHIRLPOOL MICROWAVE OVEN MODELS : MT1195SG, GT1196SH, GT1195SH, MT3185SH, 89990, 89999, 89998, (Y)KCMS185J, MT2210SJ • UL LISTED - FOR USE OVER ELECTRIC HEAT SOURCE (INCLUDING MODELS - 27”: (Y)RBS275PD, (Y)GBS277PD, KEBI171D, (Y)KEBS177D...
- Page 2 All manuals and user guides at all-guides.com STEP 1 WARNING Electrical Shock Hazard Disconnect power before installing trim kit. Replace all panels before operating. Failure to do so can result in death or electrical shock. Front 1. Disconnect the microwave oven before proceeding with installation.
- Page 3 All manuals and user guides at all-guides.com STEP 3 1. On the cutout floor, mark hole centers for the anti-tip brackets as shown using the supplied template. Be sure to align the center line of template to center line of cutout floor. 2.
- Page 4 All manuals and user guides at all-guides.com STEP 5 Pilot Hole Cutout 1. Place the trim kit frame over the microwave oven. Opening Important Note : Trim kit frame orientation is "A" important. Orient the frame so that louvers are sloping downward to the front.
- Page 5 All manuals and user guides at all-guides.com GARNITURES POUR MODÈLE ENCASTRÉ INSTRUCTIONS D´INSTALLATION (DOCUMENTS À CONSERVER) Ensemble de garnitures pour modèles Whirlpool: MK1197XH, MK1190XH • POUR UTILISATION AVEC LES FOURS À MICRO-ONDES WHIRLPOOL MODÈLES : MT1195SG, GT1196SH, GT1195SH, MT3185SH, 89990, 89999, 89998, (Y)KCMS185J, MT2210SJ •...
- Page 6 All manuals and user guides at all-guides.com ÉTAPE 1 AVERTISSEMENT Risque de choc électrique Interrormpre l´alimentation électrique avant d´installer l´ensemble de garniture. Réinstaller chaque panneau avant de faire fonctionner l´appareil. Le non-respect de ces instructions peut provoquer accident mortel ou choc électrique. AVANT 1.
- Page 7 All manuals and user guides at all-guides.com ÉTAPE 3 1. Sur le plancher d´encastrement, marquer le centre des trous pour la bride antibasculement tel qu´illustré sur le gabarit fourni. S´assurer de bien aligner la ligne centrale du gabarit à la ligne centrale du plancher d´encastrement.
- Page 8 All manuals and user guides at all-guides.com ÉTAPE 5 Avant-trou Ouverture de 1. Placer le cadre de garniture sur le four à la cavité micro-ondes. "A" Note importante : Orienter le cadre de telle manière que les lames de la claire-voie soient inclinées vers l´avant.