Hasbro NERF PRO GEL FIRE X MRBEAST Mode D'emploi page 4

1. CHARGING BATTERY
REMOVE BATTERY
Squeeze tabs and slide battery out of blaster.
1
1
2
CHARGE BATTERY
Using a USB-A to USB-C
HOURS
charging cable, insert
the USB-C end into
battery charger port.
Attach the cable to
a USB-A wall charger
(not included).
It takes approximately
2 hours to fully charge
the battery.
• Light is steady when
charging.
• Light shuts off when
USB-A to USB-C
battery is fully charged.
CHARGING CABLE
• Flashing light: Charging
issue. Unplug and replug
charging cable, and try
charging again.
Store the battery outside of / separate from the blaster.
For peak performance, fully charge battery before each
battle. Recharge when rate of fire noticeably declines.
INSERT BATTERY
1
1 2
F86720920_INST_EN_NER GELFIRE_Mythic_Beast_FAR.indd 4-5 F86720920_INST_EN_NER GELFIRE_Mythic_Beast_FAR.indd 4-5
2. HYDRATE ROUNDS
Open 1 packet and pour rounds into
container of clean tap water. It is
recommended to use at least 0.5
gallon/2 liters of water per 5,000 rounds.
If you want to hydrate only some of
the rounds in a packet and save some
Includes rechargeable
rounds for later, use the same amount
7.4V 500mAh LiPo battery.
of water. More water than recommended
Replaceable.
will not impact hydration: It is not
possible to overhydrate the rounds
or grow them too large to function in
the blaster. Make sure rounds are fully
IMPORTANT: RECHARGEABLE
submerged in water.
BATTERY INFORMATION
Retain this information for future
reference. Batteries should be
replaced by an adult.
2
WARNING :
Risk of fire, explosion, and burns. Do
not disassemble, crush, heat above
45 °C (113 °F), or incinerate. Dispose
of this battery according to your
local recycling or waste regulations
HOURS
– never disassemble. Do not use the
item near a heat source such as a
fire or heater.
BLASTER STORAGE
CAUTION :
Risk of fire and burns. Do not
1. Store the battery
open, crush, heat above 45˚C, or
outside of / separate
incinerate. Follow manufacturer' s
from the blaster.
instructions.
WARNING :
Use only with the device provided.
1
Chargers used with the product
are to be regularly examined for
1
damage to the cord, plug, enclosure
and other parts, and that, in the
event of such damage, the product
must not be used with this charger
until the damage has been repaired.
NOTE: The battery terminals are not
to be short-circuted.
3. ATTACH HOPPER
Remove cap from hopper and hold it with opening facing up.
Fill hopper with hydrated rounds.
Drain ALL water from hopper.
Holding blaster upside down, twist hopper onto blaster with
a 1/4 turn to lock it in place. Make sure hopper is securely
attached. Turn blaster right side up.
Allow rounds
to remain in
container
for about 3-4
hours to be
fully hydrated.
ROUND
STORAGE
Discard any
unused hydrated
rounds.
HOURS
2. Make sure trigger lock 3. Prior to storage, clean the blaster of
is in locked position any Nerf Pro Gelfire round residue that
when storing the blaster. remains in the hopper feed or the barrel.
Use a long soft and clean item, such as
a cotton swab, to clear debris. Clean only
with a damp cloth or a soft, clean, dry item.
2
4. FIRE
Wear the included protective eyewear
when you or anyone else nearby is using
a Nerf Pro Gelfire blaster.
Unlock trigger.
Turn selector to desired mode:
Semi-auto:
Fires a round per trigger pull.
Selector Light
Flashing
Full-auto:
Fires continuously while trigger is depressed.
Selector Light
Steady
Selector Light
Off
NOTE: Always turn selector to OFF
when not in use.
07/12/22 9:46 07/12/22 9:46