Coleman PACK-AWAY KITCHEN Instructions De Montage page 2

PACK-AWAY
WARNING:
Read instructions and warnings before set up and use.
1. Check to ensure product is not damaged, prior to use. If product is damaged, do not use.
2. Use care when setting up and taking down product to avoid pinch points.
3. Not for use by unsupervised children.
4. Never use on uneven or soft surface.
5. Weight limits for hanging items:
Spoon Rack – 1 lb. (454 g) Lantern Hook – 12 lbs. (5.4 Kg)
6. Table top not intended for grill use. Use grill support braces only.
Fig. 7
Fig. 8 6. Assemble lantern hanger
5. Attach net shelf by placing loops onto
hooks on legs as shown. (Fig. 7 & 8)
Fig. 16 Fig. 17
12. On bottom side of tabletop,
11. Lift up on hanger bracket and rotate
push latches to lock in open
to position shown (Fig. 16 & 17).
position. (Fig. 18)
Insert lantern bail.
To Store
1. Reverse Set Up procedures.
2. Place components into carry case as shown. (Fig. 23)
Fig. 23
All manuals and user guides at all-guides.com
KITCHEN
®
To Set Up
1. Unlock front latches,
open carry case and
remove all components.
(Fig. 1)
Fig. 10
Fig. 9
Fig. 11
7. Rotate bracket until it
pole by pressing down lines up with tab then
on tab and inserting to a locked push down to lock
position in the hole on other pole. position. (Fig. 12)
(Fig. 9, 10, & 11)
Fig. 18
13. Place tabletop onto braces and press down to lock into
clips on underneath side. (Fig. 19 & 20)
3. Lock front latches on
carry case. (Fig. 24)
Your Pack-Away ® Kitchen
is now ready to move or
place into storage.
Fig. 2
Fig. 1
Fig. 3
2. Unhook supports from all 4 legs then open table frame
until fully extended. (Fig. 2, 3, & 4)
Fig. 12
Fig. 13
8. Insert assembled pole into bracket
(Fig. 13). NOTE: Arrow and notch
on pole must line up with notch in
bracket for proper installation.
Fig. 19 Fig. 20
14. Insert posts of utensil rack, at a slight angle, to
lock into clips on back of table. (Fig. 21 & 22)
The Coleman Company, Inc. • 3600 North Hydraulic • Wichita, Kansas 67219 U.S.A.
1-800-835-3278 in the United States • www.coleman.com
Sunbeam Corporation (Canada) Limited • DBA Jarden Consumer Solutions
20B Hereford Street • Brampton, ON L6Y 0M1
1-800-387-6161 in Canada • www.coleman.com
Fig. 24 MADE IN CHINA
© 2011 The Coleman Company, Inc.
Coleman ® , , and Pack-Away
The Coleman Company, Inc.
3. Rotate supports to positions shown. (Fig 5)
4. Position hole in bottom of each brace over pin
Fig. 4
on support then push down to secure. (Fig. 6)
Fig. 14
9. Tighten knob on
bracket to secure.
WARNING: Do not over tighten. Over
(Fig. 14)
tightening may damage aluminum frame.
Your Pack-Away
to use and enjoy.
Fig. 21 Fig. 22
® are registered trademarks of
Fig. 6
Fig. 5
10. Attach 2 grill
support braces
and adjust width
to properly
support your grill
shape & size.
Tighten all 4
knobs to secure.
Fig. 15
(Fig. 15)
Kitchen is now ready
®
4010005157 (ECN20021139-02)