Eaton HALO AL6501FL Manuel D'instructions

AL6501FL
AL6501FLH
ENGLISH
ITEMS REQUIRED
(Purchase separately)
• Phillips screwdriver
• Adjustable wrench
• Drill with 3/16 in. drill bit
• 1/2 in. diameter flexible conduit (if applicable, length depends on application)
• 1/2 in. watertight conduit connectors (if applicable)
• Wire connectors
IMPORTANT SAFETY INSTRUCTIONS
When using product, basic precautions should always be followed, including the following:
• Read and follow these instructions.
• Heed all warnings, including below warnings AND those included on product.
• Save these instructions and warnings.
• For outdoor use only.
• cULus LISTED for wet location use.
WARNING
• Disconnect at fuse or circuit breaker before installing or servicing.
• Disconnect power and allow fixture to cool before changing bulb or handling fixture.
• Edges may cut. Handle with care.
Notice: Lamps contain mercury, dispose according to local, state, or federal laws.
For more information, visit: www.lamprecycle.org.
CAUTION
• Connect fixture to a 120 volt, 60 Hz power source. Any other connection voids
the warranty.
• Fixture should be installed by persons with experience in household wiring or by a
qualified electrician. The electrical system, and the method of electrically connecting
the fixture to it, must be in accordance with the National Electrical Code and local
building codes.
• Always use same wattage and type of bulb that was included with the fixture. Failure
to do so will void the warranty. See fixture for wattage.
• Upside down installation can result in overheating or accumulation of water in fixture.
Install right side up.
• MINIMUM 90° C SUPPLY CONDUCTORS.
• This device complies with Part 18 of the FCC Rules.
• This product may cause interference to radio equipment and should not be installed
near maritime safety communications equipment, ships at sea or other critical
navigation or communications equipment operating between 0.45-30 MHz.
All manuals and user guides at all-guides.com
Questions?/ Des questions?/ ¿Preguntas? 1-800-334-6871 ConsumerProducts@eaton.com
PACKAGING CONTENTS /CONTENU DE L'EMBALLAGE/CONTENIDO DEL PAQUETE
B. One-piece lens
A. Fixture housing with
light sensor
Boîtier du luminaire avec
détecteur de lumière
Alojamiento del accesorio
con detector de luz
F. (2) Access cover mounting screws
Instruction Manual / Manuel d'instructions/ Instrucciones
C. 65 watt fluorescent bulb
assembly Ampoule fluorescente de
Ensemble de lentille 65 watts
d'une seule pièce Bombilla fluorescente
Ensamblado del de 65 vatios
lente de una sola pieza
(attached to fixture)
(2) Vis de montage du cache d'accès
(attached to fixture)
(2) Tornillos de la cubierta de acceso
(conectado al accesorio)
MOUNTING YOUR FIXTURE
NOTE: This fixture is intended to be conduit connected
to a properly installed and properly grounded metal
weatherproof junction box (not included). All conduit
connectors, conduit, and junction boxes (sold separately)
should be UL Listed suitable for wet locations.
1. Using the pattern on the box, mark and drill holes
for mounting.
NOTE: Mount this fixture in an upright position.
2. Install the two bottom mounting screws (E) first,
leaving enough room between the mounting
screws and the mounting surface to accommodate
mounting the fixture.
3. Screw the top mounting screw (E) into the predrilled
hole and back the screw out. This will leave the hole
threaded and make installation of the fixture easier.
4. Remove access cover (D) from parts bag.
5. Install the first conduit connector and conduit
(sold separately) into the access cover (D).
6. Feed supply wires into conduit and make wiring
connections as described in "Wiring Your Fixture".
7. Attach access cover (D) to the light fixture (A)
using the two access cover mounting screws (F)
provided (Fig. 1).
NOTE: Make sure all wiring is placed into the arm
prior to tightening the access cover screws (F).
8. Using the three mounting screws (E) provided, bolt
the housing (A) to the mounting surface.
9. Connect second conduit and conduit connector at
the junction box (Fig. 2).
10. Fasten lens assembly (B) to housing (A) using the
two lens assembly lock screws (G) and two washers
(H) provided (Fig. 3).
NOTE: Washers must be used to keep the lens in place.
WIRING YOUR FIXTURE
1. Turn off the power at the main fuse/breaker box.
2. Attach ground wire that is attached to fixture
housing (A) to the junction box earth ground wire.
3. Connect the black fixture wire to the black supply wire (hot). Attach UL approved wire
connector (sold separately).
4. Connect the white fixture wire to the white supply wire (neutral). Attach UL approved wire
connector (sold separately).
NOTE: Be careful to connect the wires correctly. Make sure no bare strands of wire extend
from the wire nut or other approved wire connectors (sold separately).
1
D. Access cover
Cache d'accès
Cubierta de
acceso
G. (2) Lens assembly lock screws
(2) Vis de blocage pour assem
blage lentille
(2) Tornillos de fijación del
ensamblado del lente
E. (3) Mounting screws
(3) Vis de montage
(3) Tornillos de montaje
H. (2) Washers
(2) Arandelas
(2) Rondelles
Fig. 1
F
F
D
A
Fig. 2
A
Conduit
Conduit
connector
Junction
box
Fig. 3
A
B
H
G