Télécharger Imprimer la page

Publicité

Liens rapides

Component Shelf Model AXWG03
Preview all steps before beginning. Should any portion of these instructions be unclear, contact a qualified contractor, handyman or call us direct at 1-800-582-9595 for assistance. Do not
attempt to install this Vantage Point Product if you have any doubts as to its proper installation. CAUTION- This shelf system is intended for use only with maximum weight indicated. Use
with heavier than the maximum weights indicated may result in instability causing possible injury. Use of this product for any other purpose unless specified by Vantage Point Products is not
recommended. Think safety first!
Δ INDICATES TO NOTE CAUTION WHICH IF NEGLECTED MAY RESULT IN AN IMPROPER OR UNSTABLE ASSEMBLY.
Modelo de Anaquel Componente AXWG03
Revise todos los pasos antes de empezar. Si alguna parte de las instrucciones no queda clara, contacte a un contratista califi cado, persona habilidosa o llámenos directamente al 1-800-
582-9595 para recibir asistencia. No trate de instalar este producto de Vantage Point si tiene cualquier duda sobre su adecuada instalación. PRECAUCIÓN- Este sistema de anaqueles está
ideado para ser usado únicamente con el peso máximo indicado. Usarlo con uno mayor que el máximo peso indicado podría provocar inestabilidad causando posibles lesiones. El uso de este
producto para cualquier propósito que no sea el especifi cado por Vantage Point Products no es recomendado. ¡Piense en la seguridad primero!
Δ INDICA QUE DEBE NOTAR CIERTA PRECAUCIÓN, LA CUAL SI ES IGNORADA, PODRÍA RESULTAR EN UN ENSAMBLAJE INADECUADO E INESTABLE.
Modèle d'Étagère Composant AXWG03
L'avant-première tous les pas avant le commencement. Si n'importe quelle portion de ces instructions être peu évident, contactez un entrepreneur qualifi é, un homme à tout faire ou
appelez-nous directs à 1-800-582-9595 pour l'assistance. N'essayez pas d'installer ce Produit de Position avantageuse si vous avez des doutes quant à son installation nécessaire.
La PRUDENCE - Ce système d'étagère est destiné pour l'utilisation seulement avec le poids maximum indiqué. Utilisez avec plus lourd que les poids maximums indiqués peuvent
s'ensuivre dans l'instabilité provoquant la blessure possible. L'utilisation de ce produit pour autre but à moins que ne spécifi é par les Produits de Position avantageuse n'est pas recom-
mandée. Pensez la sécurité d'abord! Δ INDIQUE POUR NOTER LA PRUDENCE QUI SI NÉGLIGÉ PEUT S'ENSUIVRE DANS UN ASSEMBLAGE IMPROPRE OU INSTABLE.
Teilbord-Modell AXWG03
Sehen Sie alle Schritte vor dem Anfang vorher an. Wenn jeder Teil dieser Instruktionen unklar sein, sich mit einem qualifi zierten Auftragnehmer, Mann für alles in Verbindung setzt oder uns
direkt an 1-800-582-9595 für die Hilfe nennt. Versuchen Sie nicht, dieses Standpunkt-Produkt zu installieren, wenn Sie irgendwelche Zweifel betreffs seiner richtigen Installierung haben.
VERWARNUNG - ist Dieses Bord-System für den Gebrauch nur mit dem maximalen angezeigten Gewicht beabsichtigt. Gebrauch mit schwerer als die maximalen angezeigten Gewichte kann
auf Instabilität hinauslaufen, die mögliche Verletzung verursacht. Der Gebrauch dieses Produktes zu jedem anderen Zweck, wenn nicht angegeben, durch Standpunkt-Produkte wird nicht
empfohlen. Denken Sie Sicherheit zuerst!
∆ ZEIGT AN, UM VERWARNUNG ZU BEMERKEN, DIE, WENN VERNACHLÄSSIGT, AUF EINEN UNPASSENDEN ODER NICHT STABILEN ZUSAMMENBAU HINAUSLAUFEN KANN.
A
F
C
D
E
J
K
G
A
F
C
Model AXWG03 Max Total Weight: 100 lbs / 45.35 kg
or 25 lbs / 11.33kg per shelf
Modele el Peso de Max Total AXWG03: 100 libras / 45.35 kilogramos
or 25 libras / 11.33 kilogramos por anaquel
Modelez le Poids de Max Total AXWG03 : 100 livres / 45.35 kg
ou 25 livres / 11.33 kg par étagère
Modellieren Sie AXWG03 Gewicht von Max Total: 100 pfd. / 45.35 Kg
oder 25 pfd. / 11.33 Kg pro Bord
Vantage Point Products Corp • P.O. Box 2485 Santa Fe Springs, CA 90670 USA
USA Tel: 1.800.582.9595 • Canada Tel: 905.607.9994 • Web Sites: www.vanptc.com • www.thinkvp.com
All manuals and user guides at all-guides.com
M
M
N
M
H
I
P
O
L
Email: cons-serv@vanptc.com • support@thinkvp.com
FIG.
ITEM
DESCRIPTION
A
Wall Plate
Steel wall plate with tab
B
Phillips Head Screw
#14 x 2-1/2" phillips head screw
C
Pin Ring
Plastic pin ring
D
Retaining Pin
5/16" dia x 1-5/16" steel pin
E
Support Tube
36" support tube
F
Plastic Wall Plate Cover
plastic wall plate cover
G
Slide Plate
3" steel slide plate
H
Shelf Bracket
steel shelf bracket
I
Hold Down Plate
steel hold down plate (w/ bumpers)
J
Allen Screw
#1/4-20 x 7/8" button head allen screw
K
Hex Nut
#1/4-20 hex jam nut
L
Glass Shelf
15" deep x 17" wide tempered glass shelf
M
Wire Management
6" plastic snap-in cover
N
Allen Wrench
5/32" allen wrench
O
Allen Screw
#1/4-20 x 3/8" button head allen screw
P
Rubber Bumper
rubber bumper (installed at factory)
FIG.
ARTÍCULO
DESCRIPCIÓN
A
Placa de pared
placa de pared de acero con lengüeta
B
Tornillo phillips para madera
tornillo para madera de cabeza phillips #14 x 2-1/2"
C
Anillo del pasador
anillo plástico del pasador
D
Pasador de retención
pasador de acero de 5/16" de diámetro x 1-5/16"
E
Tubo de soporte
tubo de soporte de 36"
F
Cubierta plástica para
placa de paredcubierta de plástico
G
Placa corrediza
placa corrediza de acero de 3"
H
Soporte de anaquel
soporte de acero para anaquel
I
Placa de sujeción
placa de sujeción de acero (2 hoyos)
J
Tornillo Allen
tornillo Allen de cabeza de botón #1/4- 20 x 7/8"
K
Tuerca hexagonal
tuerca hexagonal de bloqueo #1/4-20
L
Anaquel de vidrio
anaquel de vidrio templado de 15" de profundidad x 17" de ancho
M
Protección del alambrado
cubierta plástica a presión de 6"
N
Llave Allen
llave Allen de 5/32"
O
Tornillo Allen
tornillo Allen de cabeza de botón #1/4-20 x 3/8"
P
Almohadilla de goma
almohadilla de goma redondeada (instalada en la fábrica)
FIG.
ITEM
DESCRIPTION
A
Wall Plate
Steel wall plate with tab
B
Phillips Head Screw
#14 x 2-1/2" phillips head screw
C
Pin Ring
Plastic pin ring
D
Retaining Pin
5/16" dia x 1-5/16" steel pin
E
Support Tube
36" support tube
F
Plastic Wall Plate Cover
plastic wall plate cover
G
Slide Plate
3" steel slide plate
H
Shelf Bracket
steel shelf bracket
I
Hold Down Plate
steel hold down plate (w/ bumpers)
J
Allen Screw
#1/4-20 x 7/8" button head allen screw
K
Hex Nut
#1/4-20 hex jam nut
L
Glass Shelf
15" deep x 17" wide tempered glass shelf
M
Wire Management
6" plastic snap-in cover
N
Allen Wrench
5/32" allen wrench
O
Allen Screw
#1/4-20 x 3/8" button head allen screw
P
Rubber Bumper
rubber bumper (installed at factory)
FIG.
ITEM
DESCRIPTION
A
Wall Plate
Steel wall plate with tab
B
Phillips Head Screw
#14 x 2-1/2" phillips head screw
C
Pin Ring
Plastic pin ring
D
Retaining Pin
5/16" dia x 1-5/16" steel pin
E
Support Tube
36" support tube
F
Plastic Wall Plate Cover
plastic wall plate cover
G
Slide Plate
3" steel slide plate
H
Shelf Bracket
steel shelf bracket
I
Hold Down Plate
steel hold down plate (w/ bumpers)
J
Allen Screw
#1/4-20 x 7/8" button head allen screw
K
Hex Nut
#1/4-20 hex jam nut
L
Glass Shelf
15" deep x 17" wide tempered glass shelf
M
Wire Management
6" plastic snap-in cover
N
Allen Wrench
5/32" allen wrench
O
Allen Screw
#1/4-20 x 3/8" button head allen screw
P
Rubber Bumper
rubber bumper (installed at factory)
QTY
2
6
1
1
1
2
3
3
3
6
6
3
3
1
6
18
CANTIDAD
2
6
1
1
1
2
3
3
3
6
6
3
3
1
6
18
QTY
2
6
1
1
1
2
3
3
3
6
6
3
3
1
6
18
QTY
2
6
1
1
1
2
3
3
3
6
6
3
3
1
6
18

Publicité

loading

Sommaire des Matières pour Vantage Point AXWG03

  • Page 1 Preview all steps before beginning. Should any portion of these instructions be unclear, contact a qualified contractor, handyman or call us direct at 1-800-582-9595 for assistance. Do not attempt to install this Vantage Point Product if you have any doubts as to its proper installation. CAUTION- This shelf system is intended for use only with maximum weight indicated. Use with heavier than the maximum weights indicated may result in instability causing possible injury.
  • Page 2 Mounting hardware supplied with system is for wood stud installation only. Hardware is not intended for metal stud installation. Please call Vantage Point Products at (800)582-9595 or see our web site www.vanptc.com for further instructions.
  • Page 3 All manuals and user guides at all-guides.com Drill all six holes, 2-1/2” deep using a 5/32"” drill bit. Step 4 Δ Caution: Drilling oversized holes may cause phillips head screws (B) to pull out. Undersized holes may cause breakage of the lag screws during installation. PASO 4.
  • Page 4 All manuals and user guides at all-guides.com Locate the shelf brackets (H) and threaded slide plates (G). Loosely install the 1/4-20 x 3/8” button head allen Step 7 FIG 1 screws (O) through the shelf bracket (H) and into the threaded slide plate (G). DO NOT TIGHTEN (FIG 1). Slide shelf bracket (H) and slide plate (G) assembly onto support tube assembly previously assembled in STEP #2 (FIG 2).
  • Page 5 All manuals and user guides at all-guides.com FIG 1: The support tube/bracket assembly can be lowered allowing the retaining pin (D) to engage into slots Step 10 FIG 1 FIG 2 in plastic pin ring (C). FIG 2: Slide the support tube/bracket assembly through the bottom wall plate. PASO 10.
  • Page 6 All manuals and user guides at all-guides.com Slide glass shelf (L) onto shelf bracket allowing glass to engage under glass hold down plate (I). Allen screws Step 13 (J) will act as a stop for glass shelf (L). Once glass shelf if positioned, secure allen screws (J) using provided allen wrench (N).
  • Page 7 All manuals and user guides at all-guides.com Recommended LCD Mount Attachment - LCD Mounts Not Included Accesorio de Montaje de LCD recomendado - Montajes de LCD No Incluidos L’Attachement de Mont de LCD Recommandé - les Monts de LCD Non Inclus Empfohlene Flüssigkristallanzeige-Gestell-Verhaftung - Nicht Eingeschlossene Flüssigkristallanzeige-Gestelle 3 Hole Nut Plate (1)
  • Page 8 All Vantage Point Products Corp. products are manufactured to ensure superior quality, performance and durability for a lifetime of use . Warranty covers the product to be free of defects in materials and workmanship under normal and reasonable use. Vantage Point Products will repair or replace, at our option, any product which proves to be defective upon our inspection.