SPARKY BUR 15E Mode D'emploi page 6

FITTING AND REMOVING THE
BATTERY PACK
To remove the battery pack from the drill firmly
press the battery release tabs (7) at either side of
the battery pack, and slide the battery backward
out of the tool.
1
Prior to inserting the battery pack ensure the
switch is in OFF position.
To install the battery pack, align rails, on the tool
with the tabs on the battery pack and slide the bat-
tery pack on to the drill. Ensure the battery pack
is sitting straight on the foot and correctly enter-
ing the runners. The battery should slide fully on
to the drill foot until the battery pack "clicks" into
position.
BATTERY CHARGING
NOTE. The battery will be fully charged after
1.5 hours, remove it from the charger after this
time.
1. Align and slide the battery pack (8) onto the
charger (9) until the battery pack latches "click"
into position. Check that there is a firm con-
nection between the battery and the charger
groove.
2
2. Plug in the charger to the wall outlet. The red
LED will be lit during the charging.
3. The battery charging time is approximately
1.5 hours. The red LED goes out when the
charging cycle is complete and the green light
goes on. Unplug the charger power cable from
the mains and then remove the battery from the
charger.
TO OBTAIN THE BEST LIFE FOR
THE BATTERY
Never allow the drill to come to a complete stand
still before recharging. The battery should be
placed on charge whenever the battery is notice-
ably running down or the drill no longer performs
a task it previously performed.
Avoid conducting short charges. Make sure that
the battery is fully charged every time by allowing
the charger to complete its full charging cycle.
Avoid allowing lose items like screws or nails etc.
to be stored with battery packs as these or similar
items can short battery packs and cause a fire or
explosion.
Always unplug the charger when not in use and
store in a dry secure place.
Avoid charging or storing your battery in tempera-
tures below 0º C and above 40º C.
6
EN
pages-BUR15-18-[13mm].indd 6
BATTERY INDICATOR
To activate the battery indicator feature first pull
the trigger switch (3) then press the battery indica-
tor button (10), this will display the level of charge
remaining in the battery. There are 3 levels of
charge low, medium and high. When the battery
indicator is showing only 1 LED (low) the battery
should be removed and put on the charger.
VII - Know your product
This drill is mainly used for drilling in wood or metal
sheet and screwdriving. Use the tool and acces-
sories only for intended applications. All other ap-
plications are expressly ruled out.
1. Keyless chuck
2. Torque adjustment/hammer selection collar
3. Trigger with variable speed control
4. Forward/reverse switch
5. Side handle
6. Side handle clamp knob
7. Battery pack release tabs
8. Rechargeable battery pack
9. Quick charger
10. Battery indicator button
11. LED Lights
12. LED Light switch
13. 2 Speed gear selector
VIII - Operation
LED WORK AREA LIGHT
The drill has 3 LED lights (11) to illuminate the work
area and improve vision when drilling in areas with
insufficient light.
To turn the LED lights on and off depress the LED
light switch (12).
4
USING THE DRILL
Use the forward/reverse switch (4) to select the
direction of rotation, then pull the trigger (3).
This trigger switch is an electronic variable speed
control which enables the user to vary the speed
continuously. The speed varies according to how
far the trigger switch is depressed, the further it is
depressed the faster the chuck will rotate and the
lighter it is depressed, the slower it will rotate.
To stop the drill, release the trigger switch.
NOTE. You can only change the direction of rota-
BUR 15E • BUR 18E
3
5
6
22.3.2006 ã. 09:05:34