Satco NUVO T8 Instructions D'installation

LED T8 REPLACEMENT LAMPS
Models: S11756
INSTALLATION AND SAFETY INSTRUCTIONS
IMPORTANT: Read before installing fixture. Retain for future reference.
WARNING:
• DANGER: Risk of shock-disconnect power before
installation.
• WARNING: Risk of fire or electric shock. LED
Retrofit Kit installation requires knowledge of luminaire
electrical systems. If not qualified, do not attempt
installation. Contact a qualified electrician.
• WARNING: Product must be installed in accordance
with the national electrical code or your local electrical
code. If you are not familiar with these codes and
requirements, contact a qualified electrician.
• WARNING: Install this kit only in luminaries that have
the construction features and dimensions shown in the
photographs and/or drawing and where the input rating
of the retrofit kit does not exceed the input rating of
the luminaire.
• WARNING: To prevent wiring damage or abrasion,
do not expose wiring to edges of sheet metal or other
sharp objects.
Do not make or alter any open holes in an enclosure of
wiring or electrical components during kit installation.
Installers should not disconnect the existing wire from
lampholder terminals to make new connections at
lampholder terminals. Instead installers should cut
existing lampholder leads away from the lampholder
and make new electrical connections to lampholder
lead wires by employing applicable connectors.
• WARNING: Luminaire wiring and electrical parts
may be damages when installing retrofit kit hardware.
Check for enclosed wiring and components.
• WARNING: Risk of fire or electric shock.
Installation of this retrofit assembly requires a person
familiar with the construction and operation of the
luminaire's electrical system and the hazard involved.
If not qualified, do not attempt installation. Contact a
qualified electrician.
• CAUTION: Risk of electric shock. Do not use if
outer lamp envelope is damaged or broken.
• Installers should examine all parts that are not intended
to be replaced by the retrofit kit for damage and replace
any damaged parts prior to installation of the retrofit kit.
• WARNING: Check the existing wiring for damage
before installing upgrade kit. Do not install if existing
wires are damaged.
The units covered by this report were intended to retrofit surface mount, Type IC or non-IC recessed mount Listed fluorescent
luminaires that use maximum 2 tubular lamps, the minimum lamp compartment dimensions are tabulated below.
Item Number-Description
S11756-40T8/LED/96-CCT/BP/2PC
© Copyright 2023 Satco Products, Inc. 10/23 v3
Minimum Lamp
Compartment Dimensions
(Length x Width x Height) (cm)
244 x 27 x 7
1
The retrofit kit is accepted as a component of a
luminaire where the suitability of the combination
shall be determined by authorities having jurisdiction.
Product must be installed by a qualified electrician
in accordance with the applicable and appropriate
electrical codes. The installation guide does not
supersede local or national regulations for electrical
installations.
Type B Lamp – intended for operation in luminaires
with traditional fluorescent-type lamp holders wired
directly to the branch circuit. This includes both
factory-wired luminaries as well as those converted
for this purpose under a retrofit program.
THIS RETROFIT KIT INCLUDES, LED TUBE,
OPERATING INSTRUCTIONS, AND FIXTURE LABEL
FOR THE DOUBLE OR SINGLE ENDED APPLICATION.
• "This luminaire has been modified and can no longer
operate the originally intended lamp," shall be marked
on the retrofit luminaire where readily visible by the user
during normal maintenance including lamping.
• Only use the control provided with or specified by
these instructions to control this lamp. This lamp will
not operate properly when connected to a standard
(incandescent) dimmer or dimming control. For dimming,
only operate at 120-277V with specific dimmer, Dim-mate
accessory, manufactured by Jiaxing Super Lighting.
• Suitable for damp locations.
• Suitable for use in enclosed luminaries.
• Suitable for use with the following emergency
equipment; SATCO Products, Inc., Model S8002,
10W Emergency LED Driver.
• This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
and (2) This device must accept any interference
received, including interference that may cause
undesired operation.
Features, applications and installation instructions
continued on pages 2-4.
Lamp Lamp-to-Lamp
Quantity Spacing (cm)
2 11
Satco Products, Inc.
Brentwood, NY 11717