Publicité
Liens rapides
© 2009, Videolarm, Inc. All Rights Reserved
SM75C12N
Vandal-Resistant Surface Mount Dome Housing
Installation and Operation Instructions for the following models:
SM75C2N
IP Network Ready, vandal resistant outdoor surface mount housing
that can be mount facing down or facing rowards the sky.
Clear dome, with 12VDC input, heater/blower, for an IPNetwork
PTZ camera.
Before attempting to connect or operate this product,
please read these instructions completely.
All manuals and user guides at all-guides.com
www.videolarm.com
CERTIFIED
81-IN5421
01-30-2009
Publicité
Manuels Connexes pour Videolarm MOOG SM75C12N
Sommaire des Matières pour Videolarm MOOG SM75C12N
- Page 1 All manuals and user guides at all-guides.com © 2009, Videolarm, Inc. All Rights Reserved SM75C12N Vandal-Resistant Surface Mount Dome Housing www.videolarm.com Installation and Operation Instructions for the following models: SM75C2N IP Network Ready, vandal resistant outdoor surface mount housing that can be mount facing down or facing rowards the sky.
- Page 2 All manuals and user guides at all-guides.com IMPORTANT SAFEGUARDS SAFETY PRECAUTIONS Read these instructions. Keep these instructions. CAUTION Heed all warnings RISK OF ELECTRIC SHOCK DO NOT OPEN Follow all instructions. Do not use this apparatus near water. CAUTION: TO REDUCE THE RISK OF Clean only with damp cloth.
- Page 3 1. NOTIFICATIONOF CLAIMS: WARRANTYSERVICE: If Purchaser believes that the Product is defective in material or workmanship, then written notice with an explanation of the claim shall be given promptly by Purchaser to Videolarm but all claims for warranty service must be made within the warranty period.
- Page 4 All manuals and user guides at all-guides.com Contents of Box Electrical Specifications SM75C12N Power 12VDC Class 2 Only 12 VDC 3.3 Amps Total Power: 47 Watts Accessories: Heater: 20 Watts/Blower: 2 Watts Camera Power: 25 Watts Max English Tools Required: .100”...
- Page 5 All manuals and user guides at all-guides.com Wall Wall Mounting Mounting WALL Use teflon tape WALL MOUNT Mount only to suitable material such as brick, Use Teflon Tape (included) to seal conduit plugs. concrete, wood, etc. (Wall mount sold separately) •...
- Page 6 All manuals and user guides at all-guides.com Surface Surface Mounting Mounting Remove the (4) side plates . Mounting Surface Securely mount housing to mounting surface. Replace should be of suitable material such as brick, side plates when complete. concrete, wood etc. •...
- Page 7 All manuals and user guides at all-guides.com POWER Power and Control Inputs (Outside of Housing) RJ45 Camera Power (+ 12 VDC) 24VAC Camera Power (- 12 VDC) Orange POWER RJ45 Camera Max 40 Watts Accessory Power (+12 VDC) Yellow Camera Orange Heater/Blower Yellow...
- Page 8 All manuals and user guides at all-guides.com Use the rubber seal when mounting housing Pull the seal over the face of the dome and up right. Center the seal over the dome. down onto the housing. • Utilice el sello de goma al montar contener encima de la •...
- Page 9 All manuals and user guides at all-guides.com Axis 214 Mounting Hole 3026 Mounting (3) #8 x 3/8” Plate Captive 2" Screw Mounting Mounting Hole Hole Install the camera to the mounting plate using (3) 3mm x 12mm bolts and lock washers. Place (3) #8x3/8” screws on the spacers and line up the mounting slots.
- Page 10 All manuals and user guides at all-guides.com Axis 215 (3) #8x3/8” 1" Captive Screw 1" MOUNTING HOLE MOUNTING HOLE 2" AXIS215-VL3026 Install the camera to the mounting plate with (4) #8 screws and lock washers provided. Place (3) #8x3/8” screws on the spacers and align the mounting slots. Slide on plate and camera then secure. •...
- Page 11 All manuals and user guides at all-guides.com Locking Screw Captive (3) #8 x 3/8” Screw Locking Keyhole Pins Slot (3) ½" Position locking pins and locking screw over slots and turn clockwise; secure the screw. Place (3) #8x3/8” screws on the spacers and line up mounting slots. Slide on plate and camera then secure. •...
- Page 12 All manuals and user guides at all-guides.com Open Screw Slots Cable Ties POWER Camera Power (24VAC) Camera Power (24VAC) Orange CONTROL RJ45 Ethernet Connector ALARMS Alarm 1 Blue Alarm 2 Violet Alarm 3 Gray Captive Common White Screw Complete the wiring to camera. Attach the camera assembly to the housing by sliding the (3) This is what the typical path of illumination will look like with the setting at 30 degrees.
- Page 13 All manuals and user guides at all-guides.com Canon VB-C50IR ½" 2539 Mounting Plate Mounting Captive Hole Screw 1" 2" Mounting Hole Mount the camera to the 2539 plate using the provided hardware. Place (3) 8 x 32 x 3/8 Phillips head screws on the top of the spacer as shown above. Slide plate in and secure. •...
- Page 14 All manuals and user guides at all-guides.com Elmo PTC-200C Captive (3) 8 x 32 x 3/8 Screw 2539 Mounting Plate ½" Mounting Hole 1" 2" Mounting Hole Place the camera onto the quick release bracket using the (4) metric 3M Phillips head screws provided.
- Page 15 All manuals and user guides at all-guides.com Elmo PTC-400C 2539 Mounting Plate ½" Mounting Hole Quick release plate 1" 2" Mounting Hole Attach quick release bracket to mounting plate using (4) #8 screws and star washer. Complete assembly as shown, then secure camera to the quick release plate. •...
- Page 16 All manuals and user guides at all-guides.com JVC VN-C30U 2539 Mounting Plate ½" 2" Mounting Hole Remove the camera plate and mount to the bracket using the (3) metric 3M Phillips head screws. Reattach plate back to the camera. Place the screws on the spacers. Secure the plate and camera. •...
- Page 17 All manuals and user guides at all-guides.com JVC VN-C655U ½" 1" Mounting 2630 Mounting Hole Plate Place the camera on the bracket with the (4) phillips head screws. Use (4) 1” spacers and (4) 1/2” spacers provided. Place the screws on the spacers. Slide on the plate and camera then secure. •...
- Page 18 All manuals and user guides at all-guides.com Pixord 261/262 ½" Mounting 2630 Mounting Hole Plate Install camera to the bracket with (3) 8x32x.5” flat head screws, nuts and washers. Place (3) 8x32x3/8”screws on the spacers. Slide on the plate and camera then secure. •...
- Page 19 All manuals and user guides at all-guides.com Sony SNCRZ30 2" 2539 Mounting Mounting Hole Plate Attach bracket with (1) 1/4x20 bolt, washer and lock washer. Place (3) 8x32x3/8”screws on the spacers. Slide on the plate and camera then secure. • Una el soporte con (1) el perno 1/4x20, la arandela y la arandela de cerradura. Coloque (3) 8x32x3/8" screws en los espaciadores.
- Page 20 All manuals and user guides at all-guides.com Toshiba IK-WB21A Mounting Hole 1" 2" 2539 Mounting Mounting Hole Plate Remove camera bracket and attach to the 2539 plate with (4) 8x32x3/8 bolts and star washers. Place (3) 8x32x3/8”screws on the spacers. Slide on the plate and camera then secure. •...
- Page 21 All manuals and user guides at all-guides.com Replacement Parts List SM75C12N Wall Mount WMSM7 Sold Separately Be sure the bracket is properly and securely mounted to a supporting structure capable of rigidly holding the weight of the entire unit. Part Number Description RPSM7501 DOME SEAL...
- Page 22 All manuals and user guides at all-guides.com Product Registration/Warranty Thank you for choosing Videolarm. We value your patronage and are solely committed to providing you with only the highest quality products available with unmatched customer service levels that are second-to-none in the security industry.