Publicité
DANGER
CARBON MONOXIDE HAZARD
For outdoor use only. Never use inside house, or
other unventilated or enclosed areas. This heater
consumes air (oxygen). Do not use in unventilated or
enclosed areas to avoid endangering your life.
• Never store propane near high heat, open flames, pilot lights, direct sunlight, other ignition sources or where
temperatures exceed 120 degrees F (49°C).
• Propane vapors are heavier than air and can accumulate in low places. If you smell gas, leave the area
immediately.
• Never install or remove propane cylinder while heater is lighted, near flame, pilot lights, other ignition sources, or
while heater is hot to touch.
• This heater is red hot during use and can ignite flammables too close to the burner. Keep flammables at least two
(2) feet from the sides & three (3) feet from the top. Keep gasoline and other flammable liquids and vapors
well away from heater.
• The propane cylinder must always be stored outdoors in a well ventilated space. Never store propane cylinder
in an enclosed area (house, garage, etc.). If heater is to be stored indoors, disconnect the propane cylinder for
outdoor storage.
BEFORE TURNING GAS SUPPLY ON
• Your heater was designed and approved for
outdoor use only. Do NOT use it inside a building,
garage, or any other enclosed area.
• Make sure surrounding areas are free of
combustible materials, gasoline, and other
flammable vapors or liquids.
• Ensure that there is no obstruction to air ventilation.
• Be sure all gas connections are tight and there are
no leaks.
• Be sure the cylinder cover is clear of debris.
• Be sure any component removed during assembly
or servicing is replaced and fastened prior to
starting.
BEFORE LIGHTING
• Heater should be thoroughly inspected before
each use, and by a qualified service person at
least annually.
• If relighting a hot heater, always wait at least 5
minutes.
• Inspect the hose assembly for evidence of
excessive abrasion, cuts, or wear. Suspected
areas should be leak tested. If the hose leaks, it
must be replaced prior to operation. Only use
the replacement hose assembly specified by the
manufacturer.
TO TURN ON THE HEATER
1. Turn on the valve on the gas supply cylinder.
2. Press and turn the variable control knob to the "HI"
position.
3. Press down the variable control knob and hold
for 20 seconds. While holding down the variable
control knob, press the igniter button several times
until the burner head flame ignites. Release the
All manuals and user guides at all-guides.com
Operation
Caution: Do not attempt to operate until you
have read & understand all of the general safety
information in this manual, and that all assembly is
DANGER
EXPLOSION - FIRE HAZARD
-8-
complete & leak checks have been performed.
variable control knob 10 seconds after the ignition.
• If a new tank has just been connected, please
allow at least one minute or more for the air in
the gas pipeline to purge out through the pilot
hole, or simply do step 3.
• When lighting the flame make sure that the
variable control knob is continuously depressed
while pressing the igniter button. The variable
control knob can be released after flame lit for
10 seconds.
• The flame can be watched and checked
from the peephole located on the base of the
burner.
• If a small flame is needed, turn the variable
control knob to the "LO" position.
4. Turn the variable control knob to the "LO" position
for 5 minutes or more before turning the knob to
desired temperature setting.
5. If the burner flame goes out accidentally or it is
blown out by wind, turn off the heater and wait
at least 5 minutes or more to let the gas dissipate
before lighting again to avoid possible gas
explosion. Repeat steps 2 through 4.
TO TURN OFF THE HEATER
1. Press and turn the control knob to the "OFF"
position.
2. Turn off the valve on the gas cylinder and
disconnect the cylinder.
Publicité
