rock space RSD0608 Guide D'installation Rapide page 2

Method 2: Extending Your WiFi Network Using WPS
1
Power on the Repeater
Plug the repeater into a power
outlet near the router in the
same room.
Wait until the PWR LED turns
solid blue.
3 Relocate the Repeater
1.
For better performance, plug the repeater into an
outlet halfway between the router and the WiFi
dead zone.
The location you choose must be within the range
of your existing WiFi network.
2.
Wait until the Signal LED turns blue. If not, relocate
the repeater closer to the router.
3.
Connect your WiFi devices to the repeater.
The repeater's SSIDs are your WiFi router's SSID with
a su x _EXT/5GEXT. The WiFi password of the repeater
is same as your WiFi router.
FAQ
Q1: I cannot login to the web UI of the repeater. What should I do?
A1: Try the following solutions:
If a WiFi device is used, ensure that your WiFi device has connected to the
repeater's WiFi network rockspace_EXT, and the Mobile Data (if any) function
is disabled.
If a computer is used, ensure that your computer has connected to the
repeater's WiFi network rockspace_EXT, and your computer has set to Obtain
an IP address automatically and Obtain DNS server address automatically.
Or unplug the Ethernet cable.
Reset the repeater, and try again.
Q2: How to reset the repeater?
A2: When the PWR LED of the repeater is solid on, press the RESET button on the
repeater with power on using a paper clip, and release. After the PWR LED turns
solid on, the repeater is restored to the factory settings.
Q3: Why is it useless to press the RST button?
A3: Please con rm long press the RST button for 8 seconds with power on.
Q4: The repeater cannot find the WiFi network of my router/modem.
What should I do?
A4: The router may be encrypted with WEP or WPA/WPA (Enterprise) algorithm.
Change the encryption type of the router to WPA-PSK or WPA2-PSK, and try
scanning again.
All manuals and user guides at all-guides.com
2
Extend Your WiFi Network
1.
Press the WPS button on the router and within 2 minutes press the WPS button
on the repeater.
PWR
2.
Wait until the Signal LED on the repeater turns solid blue. If the Signal LED does
not turn solid blue, try Method 1.
You can use Method 2 if your router has a WPS button (possible
icons of a WPS button:
Antennas upward and vertical to the ground
WiFi router
Q5: Unable to login repeater interface
A5: Con rm the situation is before or after the expansion.
a. Before the extension:
Please con rm you have connected to the correct signal of the repeater. (The
name of its wireless signal is attached to the product sticker)
Con rm the domain name (re.rockspace.local), or IP access (192.168.0.254) that
entered in the address bar is correct.
If you are unable to login, please close the browser(but not just return) and
open a new page to try again. If still failed, please wipe all the browser cache or
reboot your mobile device.
If all the solutions above are not working, we recommend that you can restore
factory settings or recharging the plug in the socket, then try to connect and login
again.
b. After the extension:
There are two ways to deal with this problem:
Method 1:
1. First, make sure that you have connected to the correct signal of the repeater.
If the SSID of the repeater is the same as the superior signal (the router signal), you
have to con rm you connected to the signal of the repeater.
After connecting to the repeater wireless signal, please con rm the IP of the
repeater signal is assigned by superior router.
Then login by this domain name: re.rockspace.local.
If failed, please cut o the power supply and re-connect the power supply. Then
you login by the domain name after the repeater extended automatically.
If the last step above doesn't work, please change to a laptop or a mobile phone
to login.
, , or ). Otherwise, use Method 1.
Press
RSD0608
Signal
Blue: Good connection
Red: Bad connection