Publicité
Les langues disponibles
Les langues disponibles
REPLACING THE FILTER
CAUTION: Unplug from outlet and allow to cool for 60 minutes before
replacing filter.
Replace the filter every six months of regular use for optimal performance.
Follow the steps below:
1. The filter is located at the bottom of the base. Gently squeeze the latches on the filter
cover to remove it.
2. Remove and replace the filter, ensuring the pull tab is still visible on top of the filter.
3. Snap the filter cover back into position.
Note: Filter must always be used to ensure proper performance.
3
WARRANTY
This appliance is warranted against defective material or workmanship for a period of one year from
the date of purchase. Any defective part will be repaired or replaced at no charge if it has not been
tampered with and appliance has been used according to these printed instructions. This warranty
3
gives you specific legal rights as well as other rights which vary from state to state.
This warranty does not cover a defect that has been caused by negligence, accidents or improper
use of the appliance. To keep your Dr. Brown's
retain your warranty, USE ONLY AS DIRECTED.
CUSTOMER SERVICE
If you experience unsatisfactory operation or have any questions/comments,
call Handi-Craft's Customer Service at 1-800-778-9001 or send an email to
info@handi-craft.com.
For purchases made outside the United States and Canada, please contact your
local distributor.
2
2
B
A
To purchase replacement filters: drbrownsbaby.com
DESIGN UNITS: MILLIMETERS
THIS DRAWING AND RELATED 3D CAD DATA
TOLERANCES UNLESS NOTED:
CONTAINS PROPRIETARY INFORMATION THAT
ARE THE PROPERTY OF
NO PLACE:
X
2.5
HANDI-CRAFT CO. AND ARE NOT TO BE
ONE PLACE:
.X
0.5
COPIED OR USED WITHOUT THE PERMISSION
TWO PLACE:
.XX
0.25
OF HANDI-CRAFT CO.
THREE PLACE:
.XXX
0.13
ANGLE:
X
0.5
INTERPET PER ASME Y14.5-1994
ANGLE:
.X
0.25
OTHER HANDI-CRAFT ENGINEERING
STANDARDS MAY APPLY
THIRD ANGLE
SOLIDWORKS
PROJECTION
2
DESIGN UNITS: MILLIMETERS
DRAWN
TOLERANCES UNLESS NOTED:
ENG APPR.
NO PLACE:
X
2.5
ONE PLACE:
.X
0.5
MFG/Q.A APPR.
TWO PLACE:
.XX
0.25
THIS DRAWING AND RELATED 3D CAD DATA
THREE PLACE:
.XXX
0.13
CONTAINS PROPRIETARY INFORMATION
ANGLE:
X
0.5
THAT ARE THE PROPERTY OF
ANGLE:
.X
0.25
HANDI-CRAFT CO. AND ARE NOT TO BE
COPIED OR USED WITHOUT THE
PERMISSION OF HANDI-CRAFT CO.
DO NOT SCALE DRAWING
INTERPET PER ASME Y14.5-1994
THIRD ANGLE
OTHER HANDI-CRAFT ENGINEERING
PROJECTION
STANDARDS MAY APPLY
MATERIAL
SOLIDWORKS
3D
2
1
D
C
B
2 f ilters are included.
HANDI-CRAFT COMPANY
4433 FLYER AVE. ST. LOUIS MO. 63116, USA
MATERIAL
DRAWN
RBW
15JUL19
ENG APPR.
3D
MFG/Q.A APPR.
DO NOT SCALE DRAWING
A
RBW
15JUL19
HANDI-CRAFT COMPANY
4433 FLYER AVE. ST. LOUIS MO. 63116, USA
TITLE:
FILTER REPLACEMENT
REV.
1
SIZE
C
DWG. NO.
SCALE: 1:1
SHEET 1 OF 1
1
Bottle Sterilizer and Dryer in good condition and
™
1
TITLE:
FILTER AND COVER
SIZE
DWG. NO.
REV.
A
1
SCALE: 1:2
SHEET 1 OF 1
1
B
A
Publicité
