Taurus LENA Mode D'emploi page 10

INSTALLATION
- Make sure you have removed all packing
material. In order to prevent possible risk of
accidents, do not leave items such as plastic
bags, polystyrene or cables within the reach of
children.
- Fully unroll the appliance's power cable before
each use.
- Clean the appliance following the appliance
cleaning instructions in this manual.
- Place the appliance on a flat, stable surface that
can withstand the weight and heat emitted from
the appliance.
INSTRUCTIONS FOR USE:
- Open the lid (1) by pressing the opening button
(2). (Fig. 1)
- Fill the body of the appliance (6) with cold
drinking water.
- Place the body of the appliance (6) on its base
(7).
- Plug the power cable in to a socket.
- Close the lid (1) of the appliance.
BASAL OPERATION:
1. Put the base on the dry, smooth and horizontal
plane.
2. Insert the plug to the socket.
3. When the kettle is inserted into the base, the
power puts through automatically to the jar.
4. Press the " " key shortly, with the beep, it
starts running.
5. After the water boils, the indicator (fig.2) turns
off and the buzzer sends out three beeps in a row
to indicate that the kettle stopped heating.
HOW TO USE "KEEP WARM" FUNCTION:
- By holding down "
second from the stand-by mode, we will hear a
beep, that means that the "keep warm" function
started running, we will see the red LED light
turning on and off constantly during the "keep
warm" function mode, the water will reach the
maximum temperature and it will keep the same
temperature for 2 hours.
- Every time that the water temperature de-
creases to 85ºC the water will boil again until
reaching the maximum temperature.
All manuals and user guides at all-guides.com
" for approximately 1
HOW TO USE TEMPERATURE SELECTOR
FUNCTION:
- Press " " for once, we can see the 60ºC
indicator light illuminated on the electronic panel
(fig.2), the green LED light indicates that the
kettle will stop heating when the water tempera-
ture reaches 60ºC.
- Press " " for twice, we can see the 70ºC
indicator light illuminated on the electronic panel
(fig.2), the blue LED light indicates that the ket-
tle will stop heating when the water temperature
reaches 70ºC.
- Press " " for three times, we can see the
80ºCindicator light illuminated on the electronic
panel (fig.2), the yellow LED light indicates
that the kettle will stop heating when the water
temperature reaches 80ºC.
- Press " " for three times, we can see the
90ºC indicator light illuminated on the electronic
panel (fig.2), the purple LED light indicates
that the kettle will stop heating when the water
temperature reaches 90ºC.
ONCE THE APPLIANCE HAS BEEN USED,
UNPLUG IT FROM THE SOCKET.
CLEANING
- Disconnect the appliance from the mains and
allow it to cool before undertaking any cleaning
task.
- Clean the electrical equipment and the mains
connection with a damp cloth and dry. DO NOT
IMMERSE IN WATER OR ANY OTHER LIQUID.
- Clean the equipment with a damp cloth with a
few drops of washing-up liquid and then dry.
- Do not use solvents, or products with an acid or
base pH such as bleach, or abrasive products,
for cleaning the appliance.
- Neither parts of this appliance are suitable for
cleaning in the dishwasher.
HOW TO DEAL WITH LIME SCALE INCRUSTA-
TIONS:
- For the appliance to work correctly it should be
kept free of limescale or magnesium incrusta-
tions caused by the use of hard water.
- To prevent this kind of problem, we recommend
the use of water with low lime or magnesium
mineralisation.
- However, if it is not possible to use the kind of
water recommended above, you should periodi-