BorMann BWR5130 Mode D'emploi page 2

EN
Safety instructions
WARNING!
1. Study, understand, and follow all instructions before operating this device.
2. Do not exceed rated capacity.
3. Use only on hard, level surfaces, with less than 3 degrees of slope.
4. Lifting device only. Immediately after lifting, support the vehicle with appropriate means.
5. Do not move or dolly the vehicle while on the jack.
6. Lift only on areas of the vehicle as specified by the vehicle manufacturer.
7. No alterations shall be made to this product.
8. Only attachments and/or adapters supplied by the manufacturer shall be used.
9. Do not get under or allow anyone under the vehicle until it has been supported by jack stands.
10. Center load on saddle prior to lifting.
11. Use wheel chocks or other blocking device on opposing wheels before using jack.
12. Never use on a lawn mower or lawn tractor.
13. Do not use this jack for any use other than the manufacturer specified usage.
14. Do not rock the vehicle while working on or around equipment.
15. This equipment is not intended for lifting foundations, homes, mobile homes, trailers, RV's, campers or fifth wheels, etc.
16. Failure to heed these markings may result in personal injury and/or property damage.
Technical Data
Model:
Capacity (Ton):
Min. height (mm):
Lifting height (mm):
Adjustable height (mm):
Net weight (kg):
Operation
Safety information shall be emphasized and understood prior to usage.
The jack shall be inspected as per the instruction manual prior to use.
It is the owner's and/or operator's responsibility to study all WARNINGS, operating, and maintenance instructions contained on the product label and
instruction manual prior to operation of this unit. The owner/operators shall retain product instructions for future reference.
Raising a vehicle
1. Make sure the jack and vehicle are on a hard level surface.
2. Always set the vehicle parking brake and block the wheels
3. Consult the vehicle owners manual to ascertain the location of jack points and position the jack beneath the prescribed lift point.
4. Turn the release valve clockwise to the closed position. DO NOT OVER TIGHTEN!
5. To raise the vehicle to designed height, place the handle into the socket and pump up and down.
6. Place the jack stands beneath the vehicle at locations recommended by the vehicle manufacturer. Do not get under the vehicle without the jack stands.
Jacks are not designed to keep heavy loads lifted for long periods of time. Do not attempt to put the jack stand simultaneously under both ends of vehicle
or under one side of vehicle.
7. Turn release valve SLOWLY counter-clockwise to lower load onto jack stands.
Lowering a vehicle
1. Turn the release valve clockwise to the closed position.
2. Pump the handle to lift vehicle off of jack stands.
3. Remove the jack stands. Do not get under or let anyone else under the vehicle while lowering.
4. Turn the release valve SLOWLY counter-clockwise to lower the vehicle onto the ground.
Inspection
The product shall be maintained in accordance with the product instructions. No alterations shall be made to this product.
1. Before use, a visual inspection of the jack should be made for abnormal conditions such as cracked welds, damage, bent, worn, loose or missing parts, or
hydraulic leaks.
2. Inspections shall be performed in accordance with this manual.
3. The product shall be inspected immediately if the jack is believed to have been subject to an abnormal load or shock. It is recommended that this
inspection be made by an authorized customer service representative prior to use.
2
BWR5142 BWR5018 BWR5019
8 Ton
2 Ton
5 Ton
190
140 185
72 110
115
48 60 60
2,4 4,2 4,9
WWW.NIKOLAOUTOOLS.GR
* The manufacturer reserves the right to make minor changes to product design and technical
specifications without prior notice unless these changes significantly affect the performance and
safety of the products. The parts described / illustrated in the pages of the manual that you hold in
BWR5130
your hands may also concern other models of the manufacturer's product line with similar features
and may not be included in the product you just acquired.
15 Ton
* To ensure the safety and reliability of the product and the warranty validity, all repair, inspection
227
or replacement work, including maintenance and special adjustments, must only be carried out
by technicians of the authorized service department of the manufacturer.
150
80
* Always use the product with the supplied equipment. Operation of the product with non-provided
equipment may cause malfunctions or even serious injury or death. The manufacturer and the
6,9
importer shall not be liable for injuries and damages resulting from the use of non-conforming
equipment.