Publicité
Les langues disponibles
Les langues disponibles
time than recommended could cause the fasteners
to be overstressed, stripped or damaged.
MAINTENANCE
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start-up can cause injury.
Accessories
WARNING: Since accessories, other than those
offered by CRAFTSMAN, have not been tested with
this product, use of such accessories with this tool
could be hazardous. To reduce the risk of injury, only
CRAFTSMAN recommended accessories should be
used with this product.
Recommended accessories for use with your tool are
available at extra cost from your local dealer or authorized
service center. If you need assistance in locating any
accessory, please contact CRAFTSMAN, call 1-888-331-4569.
Versatrack™ (Fig. F)
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start-up can cause injury.
WARNING: To reduce the risk of serious personal
injury, do not use a damaged Versatrack™ hang hook
or Versatrack™ Trackwall. A damaged Versatrack™
hang hook or Versatrack™ Trackwall will not support
the weight of the tool.
WARNING: To reduce the risk of serious personal
injury, ensure the screw holding the Versatrack™ hang
hook is securely tightened.
WARNING: To reduce the risk of serious personal
injury, DO NOT suspend tool overhead or suspend
objects from the hang hook. ONLY suspend tool on the
Versatrack™ Trackwall using the hang hook.
WARNING: Ensure that the tool weight does not
exceed the maximum rated weight for the selected
Versatrack™ hook.
WARNING: When hanging objects on a Versatrack™
Trackwall rail, adequately space the tools in order to
not exceed 75 lb (35 kg) per linear foot.
iMPORTAnT: When attaching the Versatrack™ hang
hook, use only the screw that is provided. Be sure to
securely tighten the screw. Versatrack™ accessories
mount compatible tools securely to the Versatrack™
Trackwall system.
1. Turn tool off, remove the battery pack and
remove accessories.
CAUTION: Any product with exposed cutting teeth
must have them covered securely if it is to be on
the Versatrack™ Trackwall.
2. Attach the hang hook
12
a. Place the Versatrack™ hang hook onto the mounting
location at the base of the tool.
on the tool.
b. Use a screwdriver to secure the hang hook with the
provided screw
11
. Do not use any other screw for this.
nOTE: Versatrack™ accessories for use with your tool are
available at extra cost from your local dealer or authorized
service center. If you need assistance in locating any
accessory, please contact CRAFTSMAN, call 1-888-331-4569.
Fig. F
Belt Hook (Fig. F)
Optional Accessory
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start-up can cause injury.
WARNING: To reduce the risk of serious personal
injury, ONLY use the tool's belt hook to hang
the tool from a work belt. DO NOT use the belt
hook for tethering or securing the tool to a person or
object during use. DO NOT suspend tool overhead or
suspend objects from the belt hook.
WARNING: To reduce the risk of serious personal
injury, ensure the screw holding the belt hook
is secure.
iMPORTAnT: When attaching or replacing the belt hook,
use only the screw
that is provided. Be sure to securely
11
tighten the screw.
The belt hook can be be attached to either side of the tool
using only the screw
11
provided, to accommodate left- or
right- handed users. If the hook is not desired at all, it can be
removed from the tool.
To move the belt hook, remove the screw that holds the
belt hook in place then reassemble on the opposite side. Be
sure to securely tighten the screw.
Cleaning
WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performing this.
WARNING: Never use solvents or other harsh
chemicals for cleaning the non-metallic parts of
the tool. These chemicals may weaken the plastic
materials used in these parts. Use a cloth dampened
only with water and mild soap. Never let any liquid
get inside the tool; never immerse any part of the tool
into a liquid.
English
12
11
9
Publicité
