AmazonBasics B081236VRD Mode D'emploi page 7

Decrease button
L
Timer button
M
N Flame brightness button
6. Before First Use
DANGER
Risk of suffocation!
» Keep any packaging materials away from children – these
materials are a potential source of danger, e�g� suffocation�
» Remove all the packing materials�
» Remove and review all components before use�
7. Installation Tips
WARNING
» Failure to install the product as instructed may result in damage
to the product and or may expose the user to the risk of fire,
electric shock, serious injury or death�
» This product should be installed, maintained by an experienced
adult� If in doubt, consult a professional�
» Before mounting, determine the suitable mounting location� The
product must be fixed to a wooden or masonry/concrete wall
using fasteners that are appropriate for the mounting surface�
» Do not install on drywalls, wall boards or thin plywood� The
mounting surface must be capable of supporting the weight of
the product�
8. Operation
8.1 Switching on/off
1� Connect the power cord with plug (F) to a suitable socket outlet�
2� Set the on/off switch (C) to 'I' (product in standby)� The product
beeps and the standby indicator stays lit� The product is now in
a standby mode�
3� Press the standby button (K) to switch on the product�
4� To switch off the product, press the standby button (K) again�
NOTICE
» In order to protect the product from overheating, there is a 10
second delay when switching the heater on and off� This does
not indicate malfunction�
» There may be a trace of odor during the first few minutes of
use, or after a period of storage� This is normal and quickly
disappears�
» If the product is not in use for a long period, set the on/off
switch (C) to '0' and remove the plug (F) from the socket outlet�
8.2 Setting day and time
1� Press the set date/time button (Q), the corresponding day and
SET indicator starts flashing�
2� Quickly press the increase button (I) or decrease button (L) to
select the day, then press the set date/time (Q) to confirm� The
hours indicator starts flashing�
3� Quickly press the increase button (I) or decrease button (L) to
select the hours, then press the set date/time (Q) to confirm�
The minutes indicator starts flashing�
4� Quickly press the increase button (I) or decrease button (L) to
select the minutes, then press the set date/time (Q) to confirm�
The day and time is now set�
NOTICE
The day and time can be also set by pressing and
holding the timer button (M) on the control panel�
Celsius/Fahrenheit button
O
Temperature button
P
Q Set day/time button
» Remove the protective strip on the remote controls battery
compartment�
» Check the product for transport damages�
» Before connecting the product to the power supply, check that
the power supply voltage and current rating corresponds with
the power supply details shown on the product rating label�
» The product must be installed between 0�5 and 2�5 meters
above the ground�
» For best results, install the product out of direct sunlight�
» To avoid reconstruction, install the product in a proximity of
properly grounded socket outlet�
» Do not drill into any pipes or power lines beneath the surface
during mounting holes preparation� Use voltage/metal detector
before drilling any holes to eliminate any such potential risks�
» The wall mounting bracket (E) is attached to the product when
delivered� Remove the wall mounting bracket (E) before starting
to install�
8.3 Setting temperature
NOTICE
The product must be set to HEAT 1 or HEAT 2 for
the heating function to work�
» Press the temperature button (P) repeatedly until the desired
temperature has been selected� Alternately, use buttons (I) and
(L) to increases or decrease the temperature�
» The temperature range is between 17 - 30 °C (62 - 86 °F)�
» When the room reaches the set temperature, the heating
function stops automatically�
» If the product detects a drop in temperature, the heating
function resumes automatically�
8.4 Changing power level
» Press the power level button (J) to toggle between 2 heating
modes (low and high)�
» The corresponding heat indicator (HEAT 1 or HEAT 2) lights up
on the control panel�
Low level - HEAT 1
High level - HEAT 2
» The approximate coverage with each heating mode:
Low level - HEAT 1
High level - HEAT 2
NOTICE
This product is fitted with a temperature limiting
control� If the product reaches an unsafe internal temperature of
115 °C, the product automatically switches off� To reset, unplug
the product from the socket outlet and wait 10 minutes before
plugging it back in and switching on�
EN
700 W
1300 W
8 - 10 m²
10 - 20 m²
7