Directed Electronics XPRESSKIT DLPK Guide Rapide

Fonctionnal if equipped
Lock Tach
Unlock Start Enable
Arm Door Trigger
Disarm Trunk Trigger
Trunk Hood Trigger
Trunk Trigger
Tach
conn.
(-) While Running (status)
Lock
Ignition
1
conn.
Front of the module
INSTALLATION
WITH D2D
1
D2D Cable
conn.
1
Light Green
Orange/Brown
Orange/Green
Brown
4
conn.
Back of the module
Connect wire to Remote-Starter/Alarm
Copyright © 2010, DIRECTED ELECTRONICS INC
DODGE Sprinter
Radio Off Heat Seats
Transponder Bypass Gas Door
PK3, Passlock Window Roll Down
Slidding Door Hatch
Defrost Brake Signal
8 1
Orange Yellow
N.C.
White/Red White/Black
Violet/White Gray
~
Blue/White Green
2
White/Violet Violet/Black
N.C.
Light Green Blue
Red/White
Pink
14 7
Connector 1 (Black - 4 pins): Determine the type of installation:
INSTALLATION
WITHOUT D2D
Cut off one plug of the D2D connector,
connect the blue* wire to +12V and the black* wire to ground.
*Wire colors may vary on the kit you have purchased.
N.C.
(CAN Low) Data
(CAN High) Data
N.C.
3
Connect wire to vehicle
TECHNICAL
SUPPORT
INFORMATION
ALL RIGHTS RESERVED
2008-2009
Connect:
White/Red
Violet/White
Blue/White
White/Violet
N.C.
N.C.
Hood Trigger
Door Trigger
N.C.
Unlock
Trunk
Blue*
+12V
1
Black* Ground
conn.
Twisted pair wires located
at column or near cluster
4
1 2 3 4 5 6 7 8
Brown
Brown/Red
OUTPUT INPUT
web resources:
7
www.xpresskit.com
www.xpressvip.com
www.directechs.com
U p d at e A l e r t : F i r m w a r e
updates are posted to the web on
a regular basis. We recommend
WWW.XPRESSKIT.COM
you check for firmware and/or install guide
updates prior to installation of this product.
D2D (1 way)
Connect:
8 1
Orange Yellow
White/Black White/Red
Gray
Violet/White
1
Green Blue/White
Brown
Orange/Green
violet/Black White/Violet
Orange/Brown
Lt. Green Blue Lt. Green
Light Green
Pink Red/White
4
14 7
Make the connections of the DLPK to the vehicle:
1
1.A
Connector 1 (Black):
Determine the type of installation:
INSTALLATION WITH D2D
INSTALLATION WITHOUT D2D
1.B
Connector 2 (White):
Make the connections
1.C
Connector 3 (White, located at the back of the module):
Make the connections
Press the programming switch while
inserting the main wires harness (CONN 1)
into the DLPK module.
The LED will illuminate to indicate you are
2
in programming mode, release the
programming button.
Connect the other connectors
(CONN. 2)
3
WARNING: Connector 2 can be easily
plugged in backwards.
Connect the other connectors
(CONN. 3)
5
Turn the key to the "ON" position.
Once the LED starts to flash rapidly
the key to the OFF position.
6
The LED will turn off to indicate the
module has been programmed.
The LED will flash until you press the OEM
remote lock button.
The LED will turn off to indicate the module
has been programmed.
LOCK UNLOCK
The module is now ready for use.
PANIC
DLPK
Rev.: 20100113
D2D (2 way)
8 1
Orange Yellow
White/Black
Gray
1
Green
Brown
Orange/Green
Violet/Black
Orange/Brown
Blue
Light Green
Pink Red/White
4
14 7
turn