Publicité
Les langues disponibles
Les langues disponibles
Instruction manual
CAUTION!
always be switched off at the mains
before disconnecting any plug and
EN
socket connector or extension cables.
∙
Never pass the appliance over its own cord or
extension cable, while the tool is working. Make sure
you always know where the cable is.
∙
Do not wire a power cable directly into your device
yourself. Instead, take the device to your nearest
authorized Service Center.
∙
To avoid danger, damaged power cord should
be replaced by manufacturer or its agent, or similar
qualified person.
∙
Immediately unplug the tool when its cable is
damaged or cut.
ATTENTION! DANGER OF ELECTRIC
SHOCK!
Consider working area environment. Do not expose
power tools to rain. Do not use power tools in damp
or wet locations. Keep work area well lit and dry. Try
to prevent the device from getting wet or being
exposed to humidity. Do not leave it outside
overnight. Water entering a power tool will increase
the risk of electric shock.
∙
The power supply cable should be checked
regularly and, before using it, make sure the cable is
not damaged or worn out. If the cable is not in good
condition, do not use the appliance; take it to an
authorized service Center.
∙
When tool is used outdoor, only use an extension
cable that is suitable for outdoor use and which is
marked for this specific use. Keep it away from the
working area, from damp, wet or oily surfaces and away
from heat and flammable materials.
∙
Avoid any accidental starting: make sure that the
power switch (if present) is in the «off» position, before
plugging the tool in.
∙
Remove adjusting keys or wrenches before turning
the tool on.
∙
Do not use the tool if the switch does not turn the
tool on or off. Any tool that cannot be controlled with the
switch is dangerous and must be repaired.
WARNING! During the use of certain
power tools, some dust containing
chemicals known to cause cancer,
may occur.
Some of these chemicals are: lead from lead based
All manuals and user guides at all-guides.com
The
appliance
should
paints, crystalline silica from bricks and cement and other
masonry products, arsenic and chromium from chemically
treated lumber and other dangerous products. If dust is
present, your risk from these exposures varies,
depending on how often you do this type of work. To
reduce your exposure to these chemicals, any time
you do pulverulent operations, work in a well
ventilated area and work with approved safety
equipment, such as dust masks that are specially
designed to filter out microscopic particles.
∙
If the appliance strikes a foreign body, examine the
device for signs of damage and carry out any necessary
repairs before restarting and continuing to work.
∙
If the appliance starts to vibrate abnormally, turn
it off and check for the cause immediately. Vibration is
generally a warning of trouble.
∙
Always switch off the appliance and wait until
the device completely stops whenever you leave
the
machine,
before
before changing accessories, checking, cleaning,
troubleshooting or working on the appliance.
∙
It is forbidden to move or modify any of the internal
parts of the device.
Specific safety rules
∙
Never cut materials containing asbestos because
they may generate dust dangerous to your health.
∙
To reduce your exposure to harmful chemicals that
may be content in materials you're working on: work in
a well ventilated area and work with approved safety
equipment, such as dust masks that are specially
designed to filter out microscopic particles. Connect a
dust extraction device to the tool.
∙
Use clamps or other practical way to secure and
support the workpiece to a stable platform. Holding the
work by hand or against your body is unstable and may
lead to loss of control. Don't work on any workpiece that
is too small to clamp in place.
∙
Never cut or saw in concealed areas where there
may be electric gas, or water lines. Use a suitable
detector to find such lines.
∙
Keep the cutting path free of obstacles, both above
and below.
∙
Be aware of the location and setting of the lock-on
button. If the switch is locked "ON" during the use, be
ready for emergency situations to switch it "OFF", by
first pulling the on-off switch then immediately releasing
it without pressing the lock-on button.
∙
The base plate must rest securely on its entire
surface.
∙
When working, never move your hand or finger
ahead of the saw blade.
∙
Tool can chatter or vibrate if blade speed is too slow
at beginning of cut and possibly kickback.
∙
Always pull out the mains plug before changing the
8
carrying
out
maintenance,
Publicité
