MINN KOTA i-Pilot link Guide De Référence Rapide page 2

OPERATING MODES
OPERATING MODES
CRUISE CONTROL
ENGAGING CRUISE CONTROL
1. Press the Cruise Control key on the remote.
2. Press the Speed Up or Speed Down keys to adjust the
target speed shown in the Target Gauge.
3. Press OK to accept the target speed and engage Cruise
Control.
DISENGAGING CRUISE CONTROL
1. Press the Cruise Control key on the remote.
2. Press the softkey marked Cancel.
AUTOPILOT
ENGAGING AUTOPILOT
From the remote:
1. Press the AutoPilot key on the remote.
From the Humminbird:
1. Navigation X-Press Menu: Press the MENU key.
2. Select AutoPilot and press the RIGHT Cursor key.
ADJUSTING AUTOPILOT
From the remote:
1. Use the steering keys.
From the Humminbird:
1. Navigation X-Press Menu: Press the MENU key.
2. Select AutoPilot Adjust and press the RIGHT
Cursor key.
3. Adjust: Press the RIGHT or LEFT Cursor keys.
4. Confirm: Press the CHECK/INFO key.
WAYPOINTS
MARK A WAYPOINT USING THE REMOTE
1. To save a Waypoint at the boat's position, press and hold
the Spot-Lock key.
MARK A WAYPOINT USING THE HUMMINBIRD
1. To save a Waypoint at the boat's position, press the
MARK key.
2. To save a Waypoint at the cursor position, use the
4-WAY Cursor Control key to move the active
cursor to a position on the Chart View. Then, press the
MARK key.
NAVIGATE TO A SAVED WAYPOINT USING
THE REMOTE
1. Press the GOTO key followed by the Waypoints softkey.
2. Select a Waypoint from the list and press the
OK key.
NAVIGATE TO A SAVED WAYPOINT USING
THE HUMMINBIRD
1. From the Chart View, press the GOTO key.
2. Select a Waypoint from the list, and press the RIGHT
Cursor key.
OR
1. Use the 4-WAY Cursor Control key to select a Waypoint
or position on the chart.
All manuals and user guides at all-guides.com
2. Press the GOTO key.
DISENGAGE NAVIGATING TO A WAYPOINT FROM
THE REMOTE
1. Switch to the GOTO Active Screen by pressing the
GOTO key.
2. Press the Cancel Softkey.
OR
1. Press the Steer Left or Steer Right key.
DISENGAGE NAVIGATING TO A WAYPOINT FROM
THE HUMMINBIRD
1. Navigation X-Press Menu: Press the MENU key.
2. Select Cancel i-Pilot Navigation, and press the
RIGHT Cursor key.
SPOT-LOCK
MARK/ENGAGE SPOT-LOCK USING THE REMOTE
Mark a Spot-Lock and engage using the remote
1. Press the Spot-Lock key.
2. Save (optional): Press the Save Softkey.
MARK/ENGAGE SPOT-LOCK USING
THE HUMMINBIRD
Mark a Spot-Lock at the cursor position
1. Use the 4-WAY Cursor Control key to move
the cursor to a position on the chart.
2. Navigation X-Press Menu: Press the MENU key.
3. Select Mark Spot-Lock, and press the RIGHT
Cursor key.
4. Press the EXIT key until the Navigation X-Press Menu
is closed.
Engage Spot-Lock at the boat position
1. Navigation X-Press Menu: Press the MENU key.
2. Select Spot-Lock at Vessel, and press the RIGHT
Cursor key. Spot-Lock will start immediately.
3. Save (optional): Press the MENU key. Select Save
Spot-Lock, and press the RIGHT Cursor key.
Mark a Spot-Lock and start navigation
1. Use the 4-WAY Cursor Control key to move
the cursor to a position on the chart.
2. Navigation X-Press Menu: Press the MENU key.
3. Select Spot-Lock at Cursor, and press the RIGHT
Cursor key. Navigation will start automatically.
ENGAGE SPOT-LOCK AT A WAYPOINT POSITION
1. Use the 4-WAY Cursor Control key to move the cursor to
a Waypoint on the chart.
2. Navigation X-Press Menu: Press the MENU key.
3. Select the Waypoint name > Spot-Lock.
NAVIGATE TO A SAVED SPOT-LOCK USING
THE REMOTE
1. Press the GOTO key.
2. Select a Spot-Lock from the list and press the OK key.
NAVIGATE TO A SAVED SPOT-LOCK FROM
THE HUMMINBIRD
1. Use the 4-WAY Cursor Control key to select a
Spot-Lock icon on the chart.
2. Press the GOTO key.
OR
1. Press the GOTO key.
2. Select a Spot-Lock from the saved points list.
3. Press the RIGHT Cursor key.
DISENGAGE SPOT-LOCK FROM THE REMOTE
1. Switch to the Spot-Lock Active Screen by
pressing the Spot-Lock key.
2. Press the Cancel Softkey.
OR
1. Press any manual control key (steering, prop speed, prop
on/off).
DISENGAGE SPOT-LOCK FROM THE HUMMINBIRD
1. Navigation X-Press Menu: Press the MENU key.
2. Select Cancel i-Pilot Navigation, and press the
RIGHT Cursor key.
iTRACKS
START RECORDING AN iTRACK
From the remote:
1. Home Screen > Controls > Record > OK.
From the Humminbird:
1. Main Menu: Press the MENU key twice.
2. Select the Accessories tab.
3. Select Record iTrack, and press the RIGHT
Cursor key.
4. Press the EXIT key until the menu system is closed.
STOP RECORDING AN iTRACK
From the remote:
1. Record Active Screen > StopRec softkey > Save
or Discard.
From the Humminbird:
1. Navigation X-Press Menu: Press the MENU key.
2. Select Stop Recording iTrack, and press the RIGHT
Cursor key. Save Yes or No.
NAVIGATE AN ITRACK FROM THE REMOTE
1. Press the GOTO key followed by the
iTracks softkey.
2. Select an iTrack from the list and press either
the To Start or To End softkey.
NAVIGATE AN iTRACK FROM THE HUMMINBIRD
1. Use the 4-WAY Cursor Control key to select a
Start Track icon, End Track icon, or a position on
the iTrack.
2. Press the GOTO key.
3. Use the 4-WAY Cursor Control key to select one
of the submenu actions: Navigate to Start; Navigate to
End. OR
1. Press the GOTO key.
2. Select an iTrack Start or iTrack End from the
GOTO list.
BACKTRACK
1. Humminbird Navigation X-Press Menu: Press the
Menu key.
2. Select BackTrack.
3. Note that BackTrack will create and save an iTrack
using up to the last 2 miles of the Current Track. It will
also automatically engage navigation towards the End
point of the iTrack.
ROUTES
CREATE A ROUTE ON THE HUMMINBIRD
1. In a Chart View, use the 4-WAY Cursor Control key to
select a Waypoint, Spot-Lock or position on the
chart view.
2. Press the GOTO key.
3. To add more points to the route, repeat steps
1 and 2.
4. Save (optional): Press the MENU key. Select Save
Current Route and press the RIGHT Cursor key.
NAVIGATE A ROUTE FROM THE HUMMINBIRD
1. Main Menu: Press the MENU key twice.
2. Select the Nav tab.
3. Select Waypoints, Routes, Tracks and press the
RIGHT Cursor key.
4. Use the 4-WAY Cursor Control key to select the route to
be navigated and press the RIGHT
Cursor key.
5. From the menu, use the 4-WAY Cursor Control key to
select Travel, then select Forward or Reverse.
FOLLOW THE CONTOUR
ENGAGE FROM THE HUMMINBIRD:
1. Use the 4-WAY Cursor Control key to move the cursor to
a LakeMaster contour line.
2. Press the GOTO key.
3. Using the 4-WAY Cursor Control key, perform the
following selections:
• Select Contour Offset to set the offset if desired.
• Select a navigation direction.
SET THE CONTOUR OFFSET
DURING NAVIGATION
1. Navigation X-Press Menu: Press the MENU key.
2. Select Contour Offset.
3. Press the RIGHT or LEFT Cursor keys to set
the Offset.
HIGH SPEED BYPASS
ENGAGE HIGH SPEED BYPASS
1. Press the High Speed Bypass softkey on the home
screen to set the motor speed to maximum. The rabbit
icon will change to the revert icon.
DISENGAGE HIGH SPEED BYPASS
1. Press the Revert softkey to disengage High Speed
Bypass and send you back to your previous speed.
OR
1. Press the Speed Down key to disengage the High Speed
Bypass and lower your speed from the maximum speed.
2377155 Rev C