Publicité
For heat activated operations, see Method 2 or 3,
depending on application.
Method 1: Manual Operation (Non Heat Activated)
G
B
W
Method 2: Heat Activated: If the fireplace was previously
equipped with a blower
D
B
C
A
Black
Black
F A
B
D
C
Harness X
E
THERMAL DISC
TO FIREPLACE
JUNCTION BOX
G
B
THERMAL DISC
W
VARIABLE SPEED
SWITCH
FIREPLACE BLOWER CIRCUT
HOT AIR DISTRIBUTION BLOWER CIRCUIT
1. Disconnect the two wires (A & B) from the fireplace blower.
Remove the black wire (C) from the thermal disc located on
the sensor assembly bracket and attach to the blower. Con-
nect the red wire (B) to the thermal disc. Remove the white
wire (D) from the thermal disc and connect to the blower.
2. Using the wire harness (X) supplied in this kit, attach the
male end (E) to the thermal disc. Thread the bare end of
wire "X" through the grommet located in the fireplace junc-
tion box. Attach the male flag end (F) to the flag end of the
black wire (A).
3. Connect the bare wire from harness (X) to the black wire
of the 14/2 cable running to the variable speed switch. Con-
nect the white wire to the white wire from the power cable.
The 14/2 cable should be grounded at the stud located on
the fireplace junction box cover plate.
Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON L4M 0G8 Canada
All manuals and user guides at all-guides.com
VARIABLE SPEED
SWITCH
DISTRIBUTION
BLOWER
FAN
Red
White
VARIABLE
SPEED SWITCH
VARIABLE SPEED
SWITCH
DISTRIBUTION
BLOWER
FIREPLACE
BLOWER
G
B
THERMAL DISC
W
Method 3: Heat Activated: If the fireplace is not equipped
with a blower
Use of the GD36 Thermostatic Sensor Control is recom-
mended. With the thermostatic sensor option, the Hot Air
Distribution Fan will become thermally activated.
1. Attach and secure
the sensor assembly
bracket to the securing
stud located next to the
junction box at the bot-
tom left of the unit using
the lock washer and
wing nut. Ensure that the
thermal disc touches the
firebox wall.
2. Using the two wires
(Y) supplied with this kit,
attach the flag ends to the thermal disc and pass both bare
ends through to the inside of the junction box.
3. Route a grounded 2-wire, 60hz power cable to the junc-
tion box. Connect one of the (Y) harness wires to the black
power cable and the other (Y) harness wire to the black wire
from the 14/2 cable running to the variable speed switch.
Connect the white wire to the white power cable wire. Con-
nect the ground wires of both the 14/2 cable and the power
cable to the ground stud located on the fireplace junction
box cover plate.
FINISHING:
INTERIOR WALL - Install the decorative register plate over
the distribution fan opening on the finished side of the wall.
Plugs may be needed to anchor the screws.
EXTERIOR WALL using the hot air exhaust terminal, part
#GA-72, (purchased separately) - This kit comes complete
with an extension sleeve that can be trimmed to suit the
depth of an exterior wall.
Insert the sleeve into the
wall opening and fas-
ten the exhaust hood to
the exterior wall. Make
weathertight by seal-
ing with caulking, not
supplied. Plugs may be
needed to anchor the
screws.
• 1(866)820-8686
VARIABLE SPEED
SWITCH
DISTRIBUTION
BLOWER
Thermal
Harness Y
Disc
GD36
Sensor
Assembly
Fireplace
Grommet
(Rear View)
- This kit comes complete
Hot Air
Exhaust
Sleeve
(Front View)
W415-0151 / G / 11.29.17
• www.napoleon replaces.com
Hood
Publicité
