Stanley Fatmax KFFMES340 Traduction De La Notice D'instructions Originale page 6

English @
(original instructions)
Warning! The vibration emission value during actual
use of the power tool can differ from the declared
value depending on the ways in which the tool is
used. The vibration level may increase above the
level stated.
When assessing vibration exposure to determine safety
measures required by 2002/44/EC to protect persons
regularly using power tools in employment, an estimation of
vibration exposure should consider, the actual conditions of
use and the way the tool is used, including taking account of
all parts of the operating cycle such as the times when the tool
is switched off and when it is running idle in addition to the
trigger time.
Labels on tool
The following symbols are shown on the tool along with the
:
date code:
Warning! To reduce the risk of injury, the user
must read the instruction manual.
#
Electrical safety
This tool is double insulated; therefore no
earth wire is required. Always check that the
power supply corresponds to the voltage on the
rating plate.
● If the supply cord is damaged, it must be replaced by
the manufacturer or an authorised STANLEY FATMAX
Service Centre in order to avoid a hazard.
Features
This tool includes some or all of the following features.
1. Trigger switch
2. Lock-on button
3. Saw blade locking lever
4. Blade clamp
5. Shoe plate
6. Shoe beveling lever
7. Cutting action lever
8. Shoe sleeve
@
Assembly
Warning! Before assembly, remove the battery
from the tool and make sure that the saw blade has
stopped. Used saw blades may be hot.
Fitting and removing the saw blade (fig. A)
● Hold the saw blade (11) with the teeth facing forward.
● Lift the saw blade locking lever (3) upwards.
● Insert the shank of the blade fully into the blade clamp (4)
as far as it will go.
● Release the lever.
● To remove the saw blade (11), lift the saw blade locking
lever (3) upwards and pull the blade out.
6
Fitting and removing the shoe sleeve (fig. B)
The non scratch shoe sleeve (8) should be used when cutting
surfaces that scratch easily, such as laminate, veneer, or
paint. It can also be used to protect the shoe surface during
transportation and storage.
To attach shoe sleeve:
● Place the front of the shoe plate (5) into the front of the
shoe sleeve (8).
● Lower the tool into the shoe sleeve (8). The shoe sleeve
will click securely onto the rear of the shoe.
To remove shoe sleeve:
● Grasp the shoe sleeve from the bottom at the two rear
tabs and pull down and away from the shoe plate (5).
@
Use
Warning! Let the tool work at its own pace. Do
@
not overload.
Warning! Never use the tool when the saw shoe is
loose or removed.
@
Switching on and off (fig. C)
Warning! Check that the tool is not locked ON before
connecting it to a power supply. If the trigger switch
is locked ON when the tool is connected to the power
supply, it will start immediately. Damage to your tool
or personal injury may result.
● To switch the tool on, press the trigger switch (1). The tool
speed depends on how far you press the switch.
● For continuous operation, press the lock-on button (2) and
release the variable speed switch. This option is available
only at full speed.
● To switch the tool off, release the trigger switch. To switch
the tool off when in continuous operation, press the trigger
switch once more and release it.
Bevel cutting (fig. D & E)
The shoe plate can be set to a left or right bevel angle of up
to 45°.
To set the bevel angle:
● Pull the shoe beveling lever (6) out and away from the
saw to unlock the shoe plate (5).
● Slide the shoe plate forward to release it from the 0°
positive stop position.
● Set the shoe plate to the desired bevel angle. Use a
protractor to verify angle accuracy.
● Push the shoe beveling lever (6) back towards the saw to
lock the shoe plate (5).
Note: The shoe can be beveled to the left or to the right and
has detents at 15°, 30° and 45°.
To reset the shoe for straight cuts:
● Pull the shoe beveling lever (6) out and away from the
saw to unlock the shoe plate (5).
● Rotate shoe to an angle of approximately 0° and then pull
shoe backwards to engage the 0° positive stop.