Publicité
Les langues disponibles
Les langues disponibles
•
Never use chemicals such as record sprays, antistatic sprays, benzine, or thinners to
clean compact discs. These chemicals can irreparably damage the disc's surface.
•
Discs should be returned to their cases after use. This avoids serious scratches that
could cause the Laser pickup to skip.
•
Do not expose discs to direct sunlight, high humidity, or high temperatures for extended
periods. Long exposure to high temperatures can warp the disc.
•
Do not stick paper or write anything with a ballpoint pen on the label side of the disc.
CD OPERATION
Loading and Unloading Compact Discs
1. Set the Function Selector (5) to the CD Position.
2. Lift the CD Door (14) to open the disc compartment.
3. When the door has opened, remove a disc from its case and place it carefully in the
compartment with the label side facing up. Locate 3" discs, on the central spindle in the
compartment.
4. Close the door by pressing on the corner of the disc comp artment door.
PLAY BACK
1. Load a CD into the disc compartment, and close the compartment.
2. Press the Play/Pause (29) button. The Play/Pause indicator will light up and disc play
will begin from the start of the first track of the disc.
3. At the end of the disc, the unit will switch to stop mode and the play indicator will go out.
Notes: If the disc is deeply scratched, or too dirty, disc play may not start.
If an improperly centred disc is played, noise can be heard in the mechanism. The
use of such discs should be avoided.
IMPORTANT INFORMATION
This compact disc player has built-in error compensation circuits to correct for minor defects
in a disc. There are limit s, however, to the amount of correction available.
In some cases the CD player may skip some tracks on a disc during disc play. This problem
may be caused by defects (such as scratches) on the disc being played, which are too large
for the error compensation circuits to handle.
TO STOP CD PLAY
4. Press the Stop Button (28). Disc play will stop, the Play indicator will go off, and the
display will show the total number of tracks on the CD.
5. To temporarily stop disc play (pause mode), press the Pause Button (29). Disc play will
All manuals and user guides at all-guides.com
5
6
stop at the current play position. The Play/Pause indicator will begin to flash.
6. To resume disc play, press the Play Button again. The Play indicator will light up.
Starting disc play from the beginning of a particular track
•
Press the forward or Reverse Skip Track Buttons (20/21) to select the desired track. The
number of the selected track will be shown on the CD display . Press the Play/Pause
Button (29) to start play.
To skip to the next track
1. To skip to the beginning of next track 5 while track 4 is playing.
2. Press the Skip Forward ( ) Button once to skip to the beginning of next track.
Continuously pressing the Forward Skip Track Button until the desired trade is reached.
Once the beginning of the last track is reached the CD player will not advance any
further.
To skip back to the previous track on a disc
1. To skip back to the beginning of current track. Press the skip Backward (18) once.
2
Toskip back to the beginning of previous track.
Press the skip Backward (
) Skip Track Button twice.
Continuously pressing the Reverse Skip Track Button (
back through the disc track by track. Once the beginning of the first track is reached, the
CD player will not go back any further.
PROGRAMMED DISC PLAY
It is not possible to enter programs during disc play. Press the Stop button (28) first, then follow
the instructions below.
Press the Program button (22). The following information will be displayed on the CD
Display:
Press the Forward and Reverse Skip Track buttons (21) to select the track to be stored in
location "01".
Press the Program Button (16). The first program selection is now stored in the program
memory. The Program indicator (27) will flash and will appear
) makes the CD player skip
01
03
Publicité
