Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
Installation of Steel Queen
SURELL BY FORMICA
CORIAN BY DUPONT
For all other polymer based materials, or natural stone countertops,
• Steel Queen undermount sinks have a highly polished sink rim. To highlight this unique design
feature, our installation system reveals up to 3/8" of the sink rim.
• Kindred accepts no liability for damage to the solid surface countertop, or sink fixture, during
installation.
• Inspect the sink fixture for any shipping damage, prior to installation. Do not install a damaged unit.
• Aesthetics are essential to presentation of the installed sink unit. Take the necessary care to ensure
that the exposed silicone joint is kept to a minimum, the sink is properly aligned to the cut-out, and
excess silicone is cleaned from the sink.
HARDWARE SUPPLIED BY KINDRED
Kindred has supplied within the sink carton: 3 1/2" strainers (waste assembly), a die-cut corrugated template,
homeowner's manual, and a hardware kit. The intention of the hardware kit is to clamp the sink rim to the
underside of the countertop, and backup the silicone seal.
This kit includes the following:
Machine screws
Brackets
Thumbscrews
Tee nuts
1" diameter PVC discs
Loctite Prism 401
THE FABRICATOR WILL REQUIRE:
• An assortment of clamps
• A solvent such as methyl hydrate or denatured alcohol
• Silicone sealant
• 1/2" plywood buildup
• 180 grit sandpaper
Kindred Customer Service: 1-866-687-7465
30149
All manuals and user guides at all-guides.com
Undermount Sinks
METHOD ONE
NOTE: These instructions apply only to:
refer to Installation Method Two following.
AVONITE (CLASS 1)
FOUNTAINHEAD BY NEVAMAR
Use for Method One
• Jig saw
• 1 1/2" router guide bushing
• 1/2" straight cutter bit
www.kindred-sinkware.com
Use for Method Two
0605
Publicité
Sommaire des Matières pour Kindred Steel Queen Serie
- Page 1 • Steel Queen undermount sinks have a highly polished sink rim. To highlight this unique design feature, our installation system reveals up to 3/8” of the sink rim. • Kindred accepts no liability for damage to the solid surface countertop, or sink fixture, during installation.
- Page 2 All manuals and user guides at all-guides.com FABRICATOR TEMPLATE PREPARATION • The die-cut corrugated template supplied by Kindred follows the exact size and shape of the finished countertop cut-out. • The cut-out will reveal approximately 3/8" of the mirror finished sink rim.
- Page 3 All manuals and user guides at all-guides.com TEMPLATE PREPARATION (FIGURE 1) 1/2" KINDRED CORRUGATED PLUG 1/2" PLYWOOD CUT-OUT SCRAP TEMPLATE 1 1/2" O.D. COLLAR (ROUTER GUIDE BUSHING) 3/4" 1/2" PLYWOOD TEMPLATE COUNTERTOP CUT-OUT SCRAP 1/2" STRAIGHT CUTTER BIT 1/4" HARDWARE KIT SCHEMATIC (FIGURE 2)
- Page 4 • Kindred Undermount sinks have a highly polished sink rim. To highlight this unique design feature, our installation system reveals up to 3/8” of the sink rim. • Kindred accepts no liability for damage to the natural stone or solid surface countertop, or sink fixture, during installation.
- Page 5 All manuals and user guides at all-guides.com FABRICATOR TEMPLATE PREPARATION • The die-cut corrugated template supplied by Kindred follows the exact size and shape of the finished countertop cut-out. • The cut-out will reveal approximately 3/8" of the mirror finished sink rim.
- Page 6 All manuals and user guides at all-guides.com TEMPLATE PREPARATION (FIGURE 1) 1/2" KINDRED CORRUGATED PLUG 1/2" PLYWOOD CUT-OUT SCRAP TEMPLATE 1 1/2" O.D. COLLAR (ROUTER GUIDE BUSHING) 3/4" 1/2" PLYWOOD TEMPLATE COUNTERTOP CUT-OUT SCRAP 1/2" STRAIGHT CUTTER BIT 1/4" HARDWARE KIT SCHEMATIC (FIGURE 2) GRANITE, AVONITE (CLASS 3), SWANSTONE 1/2"...
- Page 7 All manuals and user guides at all-guides.com PRÉPARATION DU GABARIT (DESSIN 1) 12,7 mm (1/2 po) GABARIT MALE EN CARTON ONDULE KINDRED GABARIT EN PARTIE DECOUPEE A, CONTREPLAQUE DE METTRE AU REBUT 12,7 mm (1/2 po) PARTIE A COLLET DE 1 1/2 po...
- Page 8 All manuals and user guides at all-guides.com PRÉPARATION DU GABARIT D’INSTALLATION PAR LE FABRICANT DU COMPTOIR • Le gabarit en carton ondulé découpé à l’emporte-pièce, fourni par Kindred, a été usiné aux dimensions et à la forme exactes de la découpure finie du comptoir.
- Page 9 9,5 mm (3/8 po). • Kindred n’accepte aucune responsabilité en cas de dommages à la surface du comptoir ou à l’évier, lors de l’installation. • Vérifier si l’évier n’a pas été endommagé au cours du transport, avant de l’installer. Ne pas installer d’évier endommagé.
- Page 10 All manuals and user guides at all-guides.com PRÉPARATION DU GABARIT (DESSIN 1) 12,7 mm (1/2 po) GABARIT MALE EN CARTON ONDULE KINDRED GABARIT EN PARTIE DECOUPEE A, CONTREPLAQUE DE METTRE AU REBUT 12,7 mm (1/2 po) PARTIE A COLLET DE 1 1/2 po...
- Page 11 All manuals and user guides at all-guides.com PRÉPARATION DU GABARIT D’INSTALLATION PAR LE FABRICANT DU COMPTOIR • Le gabarit en carton ondulé découpé à l’emporte-pièce, fourni par Kindred, a été usiné aux dimensions et à la forme exactes de la découpure finie du comptoir.
- Page 12 9,5 mm (3/8 po). • Kindred n’accepte aucune responsabilité en cas de dommages à la surface du comptoir ou à l’évier, lors de l’installation. • Vérifier si l’évier n’a pas été endommagé au cours du transport, avant de l’installer. Ne pas installer d’évier endommagé.